32
Setting the Input and Output
With HD/RGB video, since the field of view and color may vary
according to the format and device, be sure to make these
settings for each input
1
Press the [MENU] button to display the Main menu.
2
Select “3. HD/RGB Input” and then select the channel
you want to set with “1: HD/RGB SD”–“5: HD/RGB
Ch4” in the sub-menu.
●
To set SD video input to the “HD/RGB section,” select “1: HD/
RGB SD.”
You can make changes to the following parameters.
*1 Cannot be set in HD/RGB SD. Parameter numbers are in
sequence, with these parameters omitted.
*2 Enabled when Format Auto Detect is set to Manual.
*3 Enabled when Pre Scaling Mode is set to Manual.
*4 Enabled when Scaling Type is set to Manual.
* Units: horizontal (pixels) x vertical (lines) / frame rate (Hertz)
* Certain signal conditions may produce differences in the aspect
ratio and position of the RGB input. If this occurs, make
adjustments with the “8: X position,” “9: Y position,” “16:
Frequency,” “17: Phase” or other relevant settings from the menu.
You can have the V-44SW automatically determine the RGB
input signals and change the settings automatically to match
these input signals.
1
While holding down the [SHIFT] button, for at least
three seconds hold down the HD/RGB button [1]–[4]
corresponding to the channel to which the RGB
signals are being input.
Once the automatic settings are completed, all of the
HD/RGB 1–4 indicators flash.
Setting the HD/RGB Input
2. HD/RGB Input
→
HD/RGB SD, Ch Sub Menu (
☞
p. 55)
1:
Format Auto Detect
*1 *2
Function automatically distinguishes input
Auto: The input format is determined
automatically.
Manual
:
The input format is selected in
accordance with “2: Input Format.”
2: Input Format *1 *2 Selects input format
3: Pre Scaling Mode Switches scaling adjustment function
Auto: The scaling is adjusted
automatically.
Manual
:The scaling is adjusted in
accordance with “4: Manual Pre
Scaling.”
4:
Manual Pre Scaling
*3
Adjusts scaling ratio when full scaling used
This setting has no effect in the P in P
effect (p. 39) sub-screen.
5: Scaling Type Selects the scaling method
For more detailed information, refer to
“About the Scaling Type” (p. 33)
6:
Manual X Scale
*4 Adjusts the horizontal expansion ratio
7:
Manual Y Scale
*4 Adjusts the vertical expansion ratio
8: X Position Fine adjustment of the horizontal start
position
9: Y Position
Fine adjustment of the vertical start position
10: Brightness Brightness adjustment
11: Contrast Contrast adjustment
12: Saturation Saturation adjustment
13: Red Red adjustment
14: Green Green adjustment
15: Blue Blue adjustment
16: Frequency *1
Fine adjustment of the Sampling Frequency
17: Phase *1 Fine adjustment of the Sampling Phase
18: Sw Enable *1 Sets the Enable/Disable status for the
channel select buttons
For more detailed information, refer to the
column, “To Prevent Errors in Using the
Channel Select Buttons” (p. 37).
19: Input Ch Reset The sub-menu settings are returned to
their factory default settings (
☞
p. 29).
HD Signals: Compatible Input Formats
1080 59.94i / 50i: (SMPTE 274M)
720 59.94p / 50p: (SMPTE 296M)
RGB Signals: Compatible Input Formats
640x480/60
640x480/75
800x600/60
800x600/75
1024x768/60
1024x768/75
1280x768/60
1280x768/75
1280x1024/60
Automatically Setting the RGB Input
Hold down for at least three seconds.
V-44SW_e.book 32ページ ２００６年１０月２３日 月曜日 午後３時２５分