Manuals / Brands / Computer Equipment / Switch / Edirol / Computer Equipment / Switch

Edirol V-44SW E1 Backing Up the V-44SWs Settings to a Computer

1 72

Download 72 pages, 3.41 Mb

49

Using the V-44SW with Other Devices

You can back up and restore the V-44SW’s settings by

transmitting data between the V-44SW and a computer.

●

This function requires software supporting backup and restore

procedures.

●

With the V-44SW, use the “Serial Data Tool” software used in

backing up the V-440HD’s settings (for Windows XP only). This

software can be downloaded from the Roland Systems Group

website.

http://rolandsystemsgroup.net

Connect the computer and the V-44SW as shown in the

diagram below.

●

Connect the computer using an RS-232C cable (D-Sub, 9-pin

female-female cross cable).

●

If using the USB port, use a USB-to-serial adapter, and make the

settings necessary to ensure that the serial port functions

normally.

●

For details of the pin assignments for the V-44SW’s REMOTE

connector, refer to “Connector Specifications: REMOTE

Connector” (p. 62).

●

You can change the baud rate setting with “4: REMOTE

Baudrate” under “8. System” in the menu.

1

Using the computer, set the application so it is in a

standby state, waiting for data reception.

2

Press the [MENU] button to display the Main menu.

3

Select “8. System” and then select “9: All Data

Transmit” from the sub-menu.

4

Select “Yes.”

5

Press the [ENTER] button.

Transmission of the data begins. The progress of the

transfer is indicated at the bottom of the screen as a

percentage.

●

Transfer of all of the data is completed in approximately 30

seconds.

●

To cancel transmission while it is still in progress, press the

[MENU] button.

The V-44SW constantly receives data transmitted from the

computer. Use the computer’s software to transfer and restore

data to the V-44SW.

Backing Up the V-44SW’s Settings to a Computer

Making the Connections

REMOTE

connector

Serial port

V-44SW Rear Panel

RS-232C cable (cross)

FemaleFemale

Computer

Procedure

Restoring Settings From a Computer

V-44SW_e.book 49ページ２００６年１０月２３日　月曜日　午後３時２５分

Contents

Main Owners Manual Copyright 2006 ROLAND CORPORATION CAUTION IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Table of Contents Appendices 51 Operation Guide 25 Quick Guide 22 Setup and Settings Guide 13 Main Features Seamless switching of HD, RGB, and SD format video, all with this single device Features Two Video Switching Modes Effects Included Includes Panel Preset Functions USING THE UNIT SAFELY USING THE UNIT SAFELY IMPORTANT NOTES Additional Precautions Power Supply Placement Overview of the V-44SW About the Operating Modes About Channels Panel Descriptions [P in P] Button [OUTPUT FADE] Button [TIME] Knob Top Panel AC Inlet REMOTE Connector Rear Panel Setup and Settings Guide Connecting the Monitor Used for Displaying the Menus Operation Reference Owners Manual Refer to Examples for Connecting and Setting the V-44SW (p. 18). About the S-VIDEO IN Connectors and COMPOSITE IN Connectors About Formats for Video Input Through the HD/RGB IN Connectors About the RGB Input About Loop Thru About Connecting the Component Inputs and Outputs About the Ground Terminal 3. Turn on the Power and Output the Video 4. Adjusting the Video Image Quality 5. Turning Off the Power and Quitting 4-1. Adjusting the Image Quality of the Final Output Video p. 30 4-2. Adjusting the Input Video Image Quality p. 32, 34 Examples for Connecting and Setting the V-44SW Outputting to a Plasma Display <HD Size (16:9) Output> The connected data projector or LCD display needs to be set up as follows. Outputting to a Projector <Live Output of RGB Video> The connected LED display needs to be set up as follows. Outputting to an LED Display <SD Size (4:3) Output> The connected hard disk recorder needs to be set up as follows. Recording Hi-Vision Video to an HD Video Deck <HD-SDI Recording> Quick Guide Try Outputting Some Video Try Adding Some Screen Transition Effects Page Page Basic Operation About Menu Levels Getting Ready to Display Menus Turning the Power Off Fading Out the Final Output Restoring the Original Factory Default Settings (Factory Reset) Setting the Input and Output Changing the Output Format Setting the Output Format Start by making settings for the output. About Delaying the Output Preventing Errors in Switching the Output Format Compatible Output Formats RGB Signals: Compatible Input Formats HD Signals: Compatible Input Formats Setting the HD/RGB Input Automatically Setting the RGB Input About the Scaling Type Setting the SD Input If the Video is Disrupted SD Signals: Compatible Input Formats Selecting NTSC or PAL Format Displaying a Test Pattern Switching Video About the Effects Used in Switching Screens Selecting the Video Switching Mode Selecting the Video Switching Mode Switching in Preset Mode To Prevent Errors in Using the Channel Select Buttons 1 2 3 Selecting the Effects To Be Applied in Switching TRANSITION Selection Buttons and Effects About the Wipe Patterns Adding Effects to the Video Terminology Used with the P in P Effect Adding the Picture in Picture (P in P) Effect Adding Effects to the Video Advanced P in P Effect Settings About the Final Output When the P in P Effect is Off Adjusting the Field of View for the Sub-Screen Applying the Key Composite Effect About the Final Output When the Key Composite Effect is Off Registering Often-Used Settings (Panel Presets) Calling Up the Factory Preset Calling Up Presets Settings Registered to the Presets Copying Presets Exchanging Presets Between PANEL PRESET Buttons Using the V-44SW with Other Devices Switching the V-44SWs Operating Modes Using the V-44SW with a V-440HD for Multi-Screen Output Using MIDI IDI Connectors MIDI Messages Handled by the V-44SW Controlling the V-44SW from an External Device Via MIDI Linking Operation Via MIDI Temporarily Cutting Linked Operation Procedure Connection Example Controlling the V-44SW from a PR-80/50 Transmitting Settings to Another V-44SW (Bulk Dump) Making the Connections Control Using V-LINK Initial V-LINK Status Settings What is V-LINK? How to Use V-LINK Backing Up the V-44SWs Settings to a Computer Restoring Settings From a Computer Making the Connections Page Page Troubleshooting Output video is disrupted Video Output Effects Other Video images disrupted when video is switched V-44SW becoming heated Menu List Settings for the nal output are made here. About the Final Output Format 1. Output You can select from the following formats for use with the nal output. HD/RGB input settings are made here. HD/RGB SD, HD/RGB Ch Sub Menu 3. HD/RGB Input SD input settings are made here. Advanced settings key composite effects are made here. 5. Key 4. P in P/Zoom Advanced settings P in P effect are made here. 7. Panel Preset Edit 6. Wipe Select MIDI-related settings are made here. 9. MIDI Setup 8. System The V-44SWs system settings are made here. MIDI Implementation Chart MIDI Implementation Chart REMOTE Command Reference Overview of Commands PSE PANEL PRESET Select KEY Key Composite ON ZOM ZOOM Effect Setting REMOTE Command Reference XOFFFlow Control XON Flow Control DAT Data Transmission Connector Specifications REMOTE Connector HD/RGB IN OUT Connectors Inputting and Outputting RGB Signals About Connection Cables Used with the Component Inputs and Outputs Menu Settings Memo 3: Preset Play Select 7. Panel Preset Edit 6. Wipe Select Menu Settings Memo 9. MIDI Setup 6: HD/RGB On Screen Display 8. System Panel Preset Memo Block Diagram V-44SW_e.book 67 HD/RGB MIXER MIDI / SERIAL Main Specifications Others Connectors Functions Index Page This product complies with the requirements of European Directives EMC 89/336/EEC and LVD 73/23/EEC. For EU Countries NOTICE AVIS For the USA FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT DECLARATION OF CONFORMITY Compliance Information Statement V-44SW_e.book 72 04348034 06-10-1N Information OCEANIA NORTH AMERICA EUROPE As of August 1, 2006 (EDIROL-2)