Maintenance indicator

Problem

 

Cause

 

Possible Solution

 

 

 

 

 

 

Normal

Abnormal

 

 

 

 

 

 

 

 

 

 

 

 

Tempera-

Off

Red on

The internal

Blocked air intake

• Relocate the projector to

ture

 

(Standby)

temperature is

 

 

 

an area with proper

warning

 

 

abnormally

 

 

 

ventilation. (See page 8.)

indicator

 

 

high.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cooling fan

Take the projector to your

 

 

 

 

 

breakdown

 

nearest EIKI Authorized

 

 

 

 

Internal circuit

 

Dealer or Service Center

 

 

 

 

 

failure

 

for repair.

 

 

 

 

Clogged air intake

 

 

 

 

 

 

 

 

 

Lamp

Green on

Red on

The lamp does

The lamp is shut

• Disconnect the power cord

indicator

(Green

 

not illuminate.

 

down abnormally.

 

from the AC outlet, and

 

blinks

 

 

 

 

 

then connect it again.

 

when the

 

 

 

 

 

 

 

 

Time to change

Remaining lamp life

• Carefully replace the lamp.

 

lamp is

 

 

 

the lamp.

 

becomes 5% or

 

(See page 52.)

 

warming

 

 

 

 

 

 

 

less.

Take the projector to your

 

up or

 

 

 

 

 

 

 

 

 

nearest EIKI Authorized

 

Red on

The lamp does

Burnt-out lamp

 

 

turning

 

 

 

Dealer or Service Center

 

(Standby)

not illuminate.

Lamp circuit failure

 

 

off.)

 

 

 

for repair.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Please exercise care when

 

 

 

 

 

 

 

replacing the lamp.

 

 

 

 

 

 

Securely install the cover.

Power

Red on/

Green

The power

The lamp unit cover

• If the power indicator blinks

indicator

Green on

blinks

indicator blinks

 

is open.

 

in green even when the

 

Red

 

in green when

 

 

 

lamp unit cover are

 

 

the projector is

 

 

 

securely installed, contact

 

blinks

 

 

 

 

 

 

on.

 

 

 

your nearest EIKI

 

(Cooling)

 

 

 

 

 

 

 

 

 

 

Authorized Dealer or

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Service Center for advice.

 

 

 

 

 

 

 

 

Info

If the temperature warning indicator illuminates, and the projector enters standby mode, follow the possible solutions above and then wait until the projector has cooled down completely before plug- ging in the power cord and turning the power back on. (At least 10 minutes.)

If the power is turned off for a brief moment due to power outage or some other cause while using the projector, and the power supply recovers immediately after that, the lamp indicator will illumi- nate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again.

The cooling fan keeps the internal temperature of the projector constant and this function is con- trolled automatically. The sound of the cooling fan may change during operation because the fan speed may change and this is not a malfunction.

51

Page 53
Image 53
Eiki EIP-250, EIP-2600 quick start Please exercise care when