Installation - Connecting Optional Ice Maker To Water Supply

To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator from electrical power before connecting a water supply line to the refrigerator.

To Avoid Property Damage:

•Copper tubing is recommended for the water supply line.Water supply tubing made of ¼” plastic is not recommended since it greatly increases the potential for water leaks. Manufacturer will not be responsible for any damage if plastic tubing is used for supply line.

•DO NOT install water supply tubing in areas where temperatures fall below freezing.

•Chemicals from a malfunctioning softener can damage the ice maker. If the ice maker is connected to soft water, ensure that the softener is maintained and working properly.

IMPORTANT: Ensure that your water supply line connections comply with all local plumbing codes.

Before Installing The Water Supply Line,You Will Need

•Basic Tools: adjustable wrench, flat-blade screwdriver, and PhillipsTM screwdriver

•Access to a household cold water line with water pressure between 20 and 120 psi.

•A water supply line made of ¼ inch (6.4 mm) OD, copper tubing. To determine the length of copper tubing needed, you will need to measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water pipe. Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out for cleaning (as shown).

•A shutoff valve to connect the water supply line to your household water system. DO NOT use a self-piercing type shutoff valve.

•A compression nut and ferrule (sleeve) for connecting the water supply line to the ice maker inlet valve.

NOTE: Water line kit number 5303917950, available from your appliance dealer at additional cost, contains 25 feet (7.6 meters) of ¼ inch OD copper tubing, a saddle type shutoff valve (nonpiercing), (2) ¼ inch brass compression nuts, (2) ferrules/sleeves, and instructions for installing a water supply line.

To Connect Water Supply Line To Ice Maker Inlet Valve

1. Disconnect refrigerator from electric power source.

2. Place end of water supply line into sink or bucket. Turn ON water supply and flush supply line until water is clear. Turn OFF water supply at shut off valve.

3. Unscrew plastic cap from water valve inlet and discard cap.

4. Slide brass compression nut, then ferrule (sleeve) onto water supply line, as shown.

5. Push water supply line into water valve inlet as far as it will go (¼ inch). Slide ferrule (sleeve) into valve inlet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten.

6. With steel clamp and screw, secure water supply line to rear panel of refrigerator as shown.

7.Coil excess water supply line (about 2½ turns) behind refrigerator as shown and arrange coils so they do not vibrate or wear against any other surface.

8. Turn ON water supply at shutoff valve and tighten any connections that leak.

9. Reconnect refrigerator to electrical power source.

10. To turn ice maker on, lower wire signal arm (see ice maker front cover for ON/ OFF position of arm).

IMPORTANT: It takes approximately 24 hours for the ice maker to begin producing ice. Air in new plumbing lines may cause ice maker to cycle two or three times before making a full tray of ice. New plumbing may cause ice to be discolored or have poor flavor. Discard ice made during the first 24 hours.

5

Page 4 Page 6
Page 5
Image 5
Electrolux 240435506 (0408) manual Before Installing The Water Supply Line,You Will Need
Page 4 Page 6

240435506 (0408) specifications

The Electrolux 240435506 (0408) is a high-performance vacuum cleaner designed to offer efficient cleaning solutions for households. This model is particularly notable for its advanced features and cutting-edge technologies, making it a popular choice among consumers seeking reliability and effectiveness in their cleaning appliances.

One of the standout features of the Electrolux 240435506 is its powerful suction capability. The vacuum is equipped with a robust motor that provides strong and consistent suction across various surfaces, including carpets, hardwood floors, and tiles. This ensures that dirt, dust, and debris are easily lifted, making cleaning tasks quicker and more efficient.

Another significant characteristic of this model is its lightweight design. Weighing in at just a fraction of heavier vacuum cleaners, the Electrolux 240435506 is easy to maneuver and transport, allowing users to effortlessly transition from room to room. This feature is especially beneficial for those with multi-level homes, as it minimizes strain while carrying the vacuum between floors.

The vacuum cleaner also comes with a range of attachments to enhance its versatility. These include a crevice tool for reaching tight spaces, a dusting brush for delicate surfaces, and an upholstery nozzle that works perfectly on furniture and car interiors. These tools make it easy to tackle any cleaning job, whether it’s a quick pick-up or a more thorough clean.

Furthermore, the Electrolux 240435506 features a HEPA filtration system. This state-of-the-art technology captures allergens and fine particles, making it an excellent choice for allergy sufferers and pet owners. The HEPA filter not only improves indoor air quality but also extends the lifespan of the vacuum by preventing dust and debris from accumulating in the motor and other components.

The design of the vacuum is user-friendly, featuring easy-to-use controls and a simple dust container that can be emptied with just one hand. This practical approach to design ensures that using the vacuum is a hassle-free experience.

In summary, the Electrolux 240435506 (0408) combines powerful suction, lightweight maneuverability, versatile attachments, and advanced filtration technology to provide a superior cleaning solution. Its focus on user convenience and efficiency makes it an ideal choice for anyone looking to maintain a clean and healthy home environment.
Top Page Image Contents