Connecting the Dishwasher, Water Connection | Electrolux 3A instruction

Installation and Connection Instructions

Connecting the Dishwasher

Water Connection

The dishwasher is fitted with safety devices that prevent the wash water returning into the drinking water system and comply with the applicable plumbing regulations.

•The dishwasher must be connected to a cold water supply.

•The dishwasher must not be connected to open hot water appliances or instantaneous water heaters.

Permitted water pressure

Lowest permitted water pressure:	Consult your installer if the water pres-
1 bar (=10 N/cm2 =100 kPa)	sure is less than 1 bar.
Highest permitted water pressure:	In the case of a water pressure greater
10 bar (=100 N/cm2 =1 MPa)	than 10 bar, a pressure reduction valve
	must be used (available from your
	dealer).

	Connect the inlet hose
1	The water inlet hose must not be kinked, crushed or entangled when it
	is being connected up.

0Connect the threaded hose fitting (ISO 228-1:2000) on the water inlet hose to a tap with an external thread (¾ inch). Tighten the threaded hose fitting hand tight only.

3	• In order that access to the tap in the kitchen is not limited by the use
	of the dishwasher, we recommend the installation of an additional

tap, or fitting a two way adapter to the existing tap.

• If you need a longer water inlet hose than that supplied, VDE approved complete hose sets are to be used. These are available from your local Service Force Centre.

• Do not use, for connection, old hoses which have been used for another appliance.

36

Image 36

Electrolux 3A manual Connecting the Dishwasher, Water Connection, Permitted water pressure, Connect the inlet hose

Contents

Favorit 3A Tips on using the appliance Dear customerPlease read these user instructions carefully Pass them on to any subsequent owner of the appliance Contents Installation and Connection Instructions What to do, if Safety Instructions Installation, Connection and Placing into OperationChild Safety General Safety Correct Use Disposal Economical and Ecological DishwashingDisposing of the Packaging Material Disposal of Old Appliances Appliance Features and Control Panel Control Panel Multi-Display can display Prior to using for the first time Adjusting the Water SoftenerSpecial salt Your area Electronic adjustment Filling with Salt for the Water Softener Fill with dishwasher saltRemain illuminated Open the door, remove the lower Rack Turning it anticlockwise Switching Rinse Aid Supply On and Off Rinse AidThere are two ways to add rinse aid Filling with Rinse Aid Fully open the rinse aid compartment lid Adjusting Rinse Aid Dosing Daily Use Loading Cutlery and Dishes Not be washed in the dishwasher Loading Cutlery Loading Pans, Frying Pans Large Plates Load large and heavily soiled dishes in the lower basketFolded over to the left To ease the loading of large items Folded across one another Across one anotherTwo rear plate inserts in the lower Baskets can be folded across one another Loading Cups, Glasses and Coffee Services Adjusting the Height of the Upper Basket Lowering the Upper BasketRaising the Upper Basket Filling with Detergent Fill with detergent General Advice Special AdviceUse of 3 in 1/ Combi Detergent Tablets Concentrated Detergent Detergent tablets Selecting the Wash Programme Programme Table Soiling Changing/Interrupting/Cancelling Start the Wash ProgrammeWash Programme Changing the wash programme Setting or Changing the Delay Start Timer Cancelling the wash programmeSetting the delay start timer Changing the delay start Care and Cleaning Switching Off the DishwasherEmptying the Dishwasher Cleaning the Filter Stances Error messages What to do, if There are problems with the operation of the dish- washer Wash results are not satisfactoryDishes are still dirty Dishes are wet and dull Technical Data Lower rinse aid dosingThere are dried water drops on the glasses and dishes Sample loading arrangements Upper basket Lower basket with cutlery basket Installing the Dishwasher See enclosed installation instructionsBuilt-Under Dishwasher Free-Standing Appliances Plinth on free-standing appliances is not adjustable Work surface must be re-mounted Connecting the Dishwasher Water ConnectionPermitted water pressure Connect the inlet hose Water inlet hose with safety valve Please take care when installing the water inlet hose Water drain Leak Prevention System Appliance is automatically pumped out Electrical Connection Changing a fuse Connections Guarantee Conditions 08705 929 Customer CareCalls may be recorded for training purposes AEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG