Pause function | Electrolux FAVORIT 50730 specification

	Operating Instructions
	Pause function
3	The pause function can only be initiated before the drying section of
	the programme I.. If the pause function is initiated during the drying

section of the programme I the wash programme is ended.

Using the pause function the dishwasher can be temporarily stopped: 0 1. Press the ON/OFF button. The wash programme will stop.

2.All indicators will go out.

3.After a short time when the wash programme is to continue, press the ON/OFF button again. The wash programme will continue.

2	The wash programme should not be stopped for a prolonged period or
	the cooled water will need to be reheated resulting in increased energy

consumption.

Setting or changing the delay start timer

Using the delay start timer you can opt to set the wash programme to start in 3, 6 or 9 hours.

0 1. Press the ON/OFF button M.

2.Setting the delay start timer:

Press the b button until the indicator next to the number of hours of delay illuminates.

Changing the delay start timer:

As long as the wash programme has not started, you can still change the delay start set by pressing the b button. Repeatedly press the b button until all three of the time indicators are off. The selected wash programme will begin immediately.

3.Press the button for the required wash programme. The programme indicator lights up.

4.After the set number of hours the wash programme will begin.

27

Image 27

Electrolux FAVORIT 50730 manual Pause function, Setting or changing the delay start timer, Setting the delay start timer

Contents

Favorit Pass them on to any subsequent owner of the appliance Tips on using the applianceDear customer Please read these user instructions carefully Contents Installation and Connection Instructions General Safety Safety InstructionsInstallation, Connection and Placing into Operation Child Safety Correct Use Disposal of Old Appliances DisposalEconomical and Ecological Dishwashing Disposing of the Packaging Material Appliance Features and Control Panel Which fault has occurred on the dishwasher Control panelNing Panel Prior to using for the first timeAdjust the water softener Your area Ing the appropriate button Dishwasher must be switched offManual setting Electronic setting Turning it anticlockwise Filling with Salt for the Water SoftenerFill with dishwasher salt Remain illuminated Open the door, remove the lower Rack To switch off the control indicator for rinse aid Rinse aidRinse aid can be added in one of two ways Fully open the rinse aid compartment lid Filling with rinse aid Adjusting Rinse Aid Dosing Daily Use Loading Cutlery and DishesNot be washed in the dishwasher Loading Cutlery To ease the loading of large items Loading Pans, Frying Pans Large PlatesLoad large and heavily soiled dishes in the lower rack Over to the left Two rear plate inserts in the lower Folded across one anotherAcross one another To ease the loading of large items Loading Cups, Glasses and Coffee Services Adjusting the Height of the Upper Basket Lowering the Upper BasketRaising the Upper Basket Fill with detergent Filling with Detergent General Advice Special AdviceUse of 3 in 1/ Combi Detergent Tablets Detergent tablets Concentrated Detergent Soiling Selecting the Wash Programme Programme Table Open the door carefully Start the wash programmeInterrupting or ending the wash programme Washer Pause function Setting or changing the delay start timerSetting the delay start timer Changing the delay start timer Emptying the Dishwasher Care and CleaningSwitching Off the Dishwasher Load Sensing Sensor Logic Cleaning the Filter What to do, if Fault warnings are displayed Dishes are wet and dull There are problems operating the dishwasherWash results are unsatisfactory Dishes are still dirty Technical Data Decrease rinse aid dosingThere are dried water drops on the glasses and dishes Upper basket Lower basket with cutlery basket Sample loading arrangements Free-Standing Appliances Installing the DishwasherSee enclosed installation instructions Built-Under Dishwasher Work surface must be re-mounted Plinth on free-standing appliances is not adjustable Connect the inlet hose Connecting the DishwasherWater Connection Permitted water pressure Please take care when installing the water inlet hose Water inlet hose with safety valve Water drain Leak Prevention System Appliance is automatically pumped outOff Changing a fuse Electrical Connection Connections Guarantee Conditions 08705 929 Customer CareCalls may be recorded for training purposes AEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG