L Y R I C 5 0

5.CONNECTING TO GAS

This appliance is designed to be installed with an appliance flexible connection only. Supply piping should not be less than R³/8 (³/8" B.S.P.). Connection is made to the Rc½ (½" B.S.P.) female threaded entry pipe located just below the hotplate level on the rear left hand side of the appliance.

Check for gas soundness after connecting the gas supply.

The gas bayonet connector must be fitted in the shaded area indicated in Fig. 3. Take into account that it must be possible to pull the appliance forward sufficiently. The

hose must not get caught on the stability bracket.

Fig.3

All dimensions in mm

IMPORTANT: FLEXIBLE TUBING USED MUST COMPLY WITH BS. 669 CURRENT EDITION. L.P.G. FLEXIBLE CONNECTIONS MUST BE OF A TYPE SUITABLE FOR L.P.G. AND CAPABLE OF OPERATION UP TO 50MBAR AND TO CARRY A RED STRIPE, BAND OR LABEL.

NOTE: ONLY LIQUID SEALANTS CAN BE USED IN THREADED GAS CONNECTIONS. DO NOT USE P.T.F.E. TAPE.

6.FITTING THE BATTERY

1.The battery holder is located at the front left hand side of the bottom storage compartment (see Fig. 4).

2.Open bottom compartment flap to gain access to the battery holder.

3.

From inside the bottom compartment, lift the battery

Fig.4

 

holder lid and fit the 1.5 volt battery (see Fig.4)

 

 

ensuring it is fitted as indicated by the symbols on the

 

4.

battery holder.

 

After fitting battery close lid of holder.

 

7.PRESSURE TESTING

1.The oven injector is used as the pressure test point.

Remove the oven furniture. Remove oven burner box retaining clips (one spring clip from each side) and remove box front cover. Replace one clip back into the right hand side of the burner box.

Remove oven burner by removing the spring clip from the right hand side of the oven burner and slide the burner off the injector whilst easing it towards the front of the appliance, taking care not to strain the F.S.D. phial.

2.Connect the pressure gauge to the oven injector.

3.Check the supply pressure by turning the thermostat on and one hotplate tap full on and light the

appropriate burner.

The pressure should be either:

(i)

For Natural Gas

20mbar

(ii)

For LP.Gas

The pressure must be set to 28 mbar for use on butane or 37 mbar for use

 

 

on propane.

4.Turn off the taps, disconnect the pressure gauge and replace oven burner and cover, ensuring that the F.S.D. phial is correctly located into the bracket on the burner.

5.Check operation of oven.

36

Page 35 Page 37
Page 36
Image 36
Electrolux Lynic 50 installation instructions Connecting to GAS, Fitting the Battery, Pressure Testing
Page 35 Page 37

Lynic 50 specifications

The Electrolux Lynic 50 is a cutting-edge vacuum cleaner designed to tackle modern cleaning challenges with ease and efficiency. It seamlessly blends powerful suction capabilities with advanced technologies, making it a suitable choice for a wide range of households.

One of the standout features of the Lynic 50 is its powerful suction. Engineered with a high-performance motor, it can handle various types of flooring, from plush carpets to hard surfaces. This versatility ensures that no dirt, dust, or pet hair is left behind, making it an ideal tool for families and pet owners alike.

A notable innovation in the Lynic 50 is its Smart Sensor Technology. This system automatically adjusts the suction power based on the type of surface being cleaned. For instance, it ramps up the suction on carpets to remove deeper-seated dirt and reduces it on hardwood floors to prevent damage. This technology not only enhances cleaning efficiency but also prolongs the life of your floors.

The Electrolux Lynic 50 also prioritizes user convenience with its lightweight design. Weighing in at just over 5 kg, it is easy to maneuver around the home. Its ergonomic handle and compact size make it simple to reach tight corners and high surfaces, reducing the strain associated with prolonged cleaning sessions.

For added convenience, the Lynic 50 boasts a large capacity dustbin, allowing users to clean more without the need for frequent emptying. The bin is designed for easy detachment and cleaning, promoting a hassle-free maintenance routine. Additionally, the vacuum features a HEPA filtration system that captures 99.97% of allergens, making it an excellent choice for allergy sufferers.

Another impressive characteristic of the Lynic 50 is its quiet operation. Unlike many traditional vacuum cleaners, the Lynic 50 operates at a lower noise level, ensuring that you can clean your home without disturbing others. This makes it particularly beneficial for nighttime cleaning or in households with small children.

In summary, the Electrolux Lynic 50 is a powerful, efficient, and user-friendly vacuum cleaner equipped with Smart Sensor Technology, a lightweight design, a large capacity dustbin, and HEPA filtration. Its combination of features makes it a top contender in the vacuum market, suited for anyone looking to maintain a clean and healthy living environment.
Top Page Image Contents