Manuals / Brands / Computer Equipment / Power Supply / Emerson / Computer Equipment / Power Supply

Emerson 10-30kVA 2.3.4 Output Dry Contacts, 2.3.5 EPO InputOptional Firmware Before M200

1 80

Download 80 pages, 3 Mb

Electrical Connections

17

2.3.4 Output Dry Contacts

There are three output dry contact relays at the X1 slot (see Figure10 and Table 4).

Figure 10 Output dry contacts and EPO wiring for firmware before M170

2.3.5 EPO Input—Optional Firmware Before M200

The UPS has an Emergency Power Off (EPO) function that operates by a button on the control panel

or by a remote contact provided by the user. The EPO button is under a hinged, clear plastic shield.

The X2 slot, shown in Figure 10, is the remote EPO input interface. It is active when shorted from

EPO-L to EPO-H.

If an external Emergency Stop facility is required, it is connected terminals EPO-L to EPO-H of the

auxiliary terminal block (X2). It also is connected to the Normally Open remote stop switch between

these two terminals using shielded cable (see Figure 10 and Table 5). If this function is not used,

terminals EPO-L to EPO-H must be opened.

Table 4 Output dry contact relays

Position Name Description

J13.2 BFP_O Bypass feedback protection relay. Normally open. Closed when bypass SCR is shorted.

J13.3 BFP_S Bypass feedback protection relay center

J13.4 BFP_C Bypass feedback protection relay. Normally closed. Open when bypass SCR is shorted.

J21.2 INV_O Inverter mode relay. Normally open. Closed when UPS is in inverter mode.

J21.3 INV_S Inverter mode relay center

J21.4 INV_C Inverter mode relay. Normally closed. Open when UPS is in inverter mode.

J25.2 ACF_O Main input fault relay. Normally open. Closed when main input is in fault.

J25.3 ACF_S Main input fault relay center

J25.4 ACF_C Main input fault relay. Normally closed. Open when main input is in fault.

NOTE

All auxiliary cables of terminal must be double-insulated. Wire should be 20-16AWG stranded

for maximum runs between 82 and 164 feet (25-50m), respectively.

Table 5 EPO input contact relays

Position Name Description

J28.2 EPO_L Emerge ncy Power Off Lo w

J28.4 EPO_H Emergency Power Off High

NOTE

The Emergency Stop action within the UPS shuts down the rectifier, inverter and static

bypass. It does not internally disconnect the input power supply.

To disconnect ALL power to the UPS, open the upstream feeder breaker(s) when the remote

EPO is activated.

EPO-L

EPO-H

X2X1

BFP_C

J21 J25 J28

BFP_S

BFP_O

INV_O

INV_S

INV_C

ACF_C

ACF_S

ACF_O

+12V

J13

Contents

Main Page TABLE OF CONTENTS Page FIGURES TABL ES IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS !WARNING Battery Cabinet Precautions GLOSSARY OF SYMBOLS ! i 1.0 I 1.1 External Inspections 1.2 Internal Inspections 1.2.1 Storing for Delayed Installation 1.3 Preliminary Checks 1.3.1 Identification 1.4 UPS Location 1.4.1 Positioning the UPS 1.4.2 Environmental Considerations 1.5 Considerations in Moving the NX Final Position 1.6 Mechanical Considerations 1.6.1 Clearances 1.6.2 Floor Installation 1.6.3 Cable Entry 10-30kVA UPS System Composition NX NX 2.0 ELECTRICAL CONNECTIONS 2.1 Power Cabling 2.1.1 Cable Rating Lug Size and Torque Requirements 2.1.2 UPS Input Configuration 2.1.3 Cabling Guidelines 2.1.4 Cable Connections B 2.1.5 Safety Ground 2.1.6 Protective Devices UPS Rectifier and Bypass Input Supply System Output 2.1.7 Cabling Procedure Common Input Connections Dual Input Connections Output System ConnectionsEnsure Correct Phase Rotation Internal UPS Battery Connections 2.2 Control Cables 2.2.1 Monitor Board Features Figure 7 Auxiliary terminal block detail (Monitoring Board) 2.3 Dry Contacts The UPS provides input dry contacts and output dry contacts. 2.3.1 Input Dry Contacts There are several input dry contacts at the X3 slot. Figure 8 Input dry contacts Table 1 Input dry contacts at X3 2.3.2 Maintenance Bypass Cabinet Interface 2.3.3 BCB Box Interface 2.3.4 Output Dry Contacts 2.3.5 EPO InputOptional Firmware Before M200 Firmware M200 or Later 3.0 BATTERY INSTALLATION 3.1 Introduction 3.2 Safety 3.3 UPS Batteries 3.4 External Battery Cabinet Installation 3.4.1 Matching Battery Cabinets 3.4.2 Connecting the Batteries Figure 13 Narrow battery cabinet, 27 in. (690mm) - rear view Figure 14 Wide battery cabinet, 57 in. (1488mm) - front view 3.4.3 Installation Considerations Figure 15 Internal cable wiring from battery cabinet to Liebert NX Figure 16 Battery tray and supports 3.4.4 Connecting the Battery Cabinet to the UPS 3.5 Non-Standard Batteries Maintenance Bypass Cabinet 25 4.0 MAINTENANCE BYPASS CABINET 4.1 Bypass Switch 4.2 Normal (UPS) Mode 4.3 Bypass Mode 4.4 Maintenance Mode 4.5 Locating the Cabinet 4.6 Cable Installation 4.6.1 Wiring Preparation 4.6.2 Power Cable Installation 4.6.3 Input/Output Wiring Page 4.7 Bolting Cabinets Together 5.0 O 5.1 Load Bus Synchronization 5.1.1 Performance Requirements 5.1.2 DBS Cable and Settings 5.2 Configuring Parallel System Operation 5.2.1 General 5.2.2 Features of Parallel System 5.2.3 Operating Principles Redundancy Paralleling 5.2.4 Operation Modes Summary 5.3 Installing Parallel System 5.3.1 Conditions for Parallel System 5.3.2 Cabinet Installation 5.3.3 Preliminary Checks 5.3.4 Protective Devices UPS Appendix 34 Figure 24 Auxiliary dry contact cables for output breaker in multi-module system Q1Ext Q2Ext QnExt Input Distribution UPS 1 UPS 2 UPS N To Load Page 5.4 Battery Circuit Breaker Box Options 37 Figure 27 Battery circuit breaker box connections J10.3 Bottom View Midpoint Busbar Detail J10.2 6.0 UPS S 6.1 Conformity and Standards 6.3 UPS Mechanical Characteristics 6.2 UPS Environmental 6.4 UPS Electrical Characteristics Table 10 UPS terminal 6.4.1 Battery Manufacturers and Models 6.4.3 DC Intermediate Circuit 6.4.2 Input Rectifier Table 11 Approved batteries Table 12 Rectifier input power 6.4.4 Inverter Output 6.4.5 Bypass Input Table 14 Inverter output Table 15 Bypass input 7.0 INSTALLATION DRAWINGS Figure 29 Dimensions continuedtop and bottom views Figure 30 Main componentstypical unit Front View (with door open) Page Page -N+ TOP LAYER MIDDLE LAYER BOTTOM L AYE R Page Page Figure 36 NX 1+1 parallel cabinet interconnections Table 18 Liebert-supplied interconnect wiring 1+1 Parallel Cabinet (Front View Without Front Door and Panel) Page Page Page UPS Module Left Side View (without side panel) Page Page Page Page Page 8.0 SPECIFICATIONS AND TECHNICAL DATA 8.1 Lug Size and Torque Requirements Table 28 Battery torque rating Table 29 Maintenance bypass cabinet electrical data (single input) Table 30 Maintenance bypass cabinet electrical data (dual input) Table 29 Maintenance bypass cabinet electrical data (single input) (continued) Table 31 Multi-module bypass cabinet electrical data Table 30 Maintenance bypass cabinet electrical data (dual input) Page Page Page Page Page Table 32 Maintenance bypass cabinet lug sizes Table 33 Battery cabinet physical characteristics Table 32 Maintenance bypass cabinet lug sizes (continued) Table 34 Maintenance Bypass Cabinet weights 8.2 Cable Lengths: Floor to Connection Point Inside UPS Table 35 Maintenance bypass cabinet dimensions Table 36 Multi-module paralleling cabinet dimensions Table 37 Distance to connection points on the NX UPS Page Page Page Ensuring The High Availability 0f Mission-Critical Data And Applications. Technical Support / Service Locations