Playback messages / deleting messages
Press 
button. The messages will be played one after the other. If there are new messages, only these will be played.
During playback
Press
button to go to the beginning of the current message.
Press
button twice to go to the previous message.
Press 
button to go to the next message.
Press 
button to pause playback (Pause), and restart playback.
Press
button to stop playback (Stop).
Press 
button to delete the current message, press and HOLD 
for approxi-
mately 2 seconds until “dL” appears in the display. Press 
once again.
In idle state
Press 
button to delete all old messages (already heard), press and HOLD
for approximately 2 seconds until “dL” appears in the display. Press 
once again. You’ll hear a confirmation announcement
Remote access code - checking / setting
You need a
Press briefly |
|
|
|
|
| to check the setting. |
|
| ||||
|
|
|
|
| ||||||||
Press and HOLD |
|
|
|
|
|
| to enter setting mode. Use | and | to set the first digit. | |||
|
|
|
|
|
| |||||||
Press briefly |
|
|
| for confirmation, and to get to the next digits input. Follow this | ||||||||
|
|
| ||||||||||
procedure for entering the digits and confirm by pressing 
. You will hear a repeat confirmation of code.
Outgoing message - setting / checking / recording / deleting
Press and HOLD 
to select the OGM (outgoing message).
Press and HOLD 
until you hear a short beep. Speak your own new outgoing
message. Stop recording by pressing 
. You hear the new OGM.
Press briefly 
to check the OGM at any time.
It is only possible to select an outgoing message if the answering machine is turned on. If the memory is full, only outgoing message 2 can be selected (only answering without recording messages).
Remote access
For remote access you need a telephone using tone dialing (DTMF).
Call your number, If the answering machine is set to off it will pick up the line after 10 ring signals. If it set to on it will pick up the line after the 
button.9
Flash time
You can set the flash time to 100 ms (usually for special services of your telephone provider/delivery state) or 600 ms (e.g. for a telephone exchange). In case of questions please contact your telephone provider or the system administrator of your PBX.
Press the MENUOK button. Select BASE using 
/ 
and press the MENUOK button.
Using | / | select RECALL and press the MENUOK button. | button. |
Using | / | select SHORT or LONG and press the OK | |
|
| MENU | |
OR
Press and HOLD the REDIAL button for approximately 3 seconds. S (100ms) or L (600ms) appears in the display.
System PIN
In delivery state the PIN is set to “000”. The PIN is valid for all registered handsets.
Press the | MENUOK button. Select BASE using / | and press the MENUOK button. |
Using / | select SYSTEM PIN and press the | MENUOK button. Enter the old PIN and |
confirm by pressing the MENUOK button. Enter the new PIN twice and confirm each by pressing the MENUOK button.
Registering a handset
Up to five handsets can by registered to a base station. The handsets delivered with your telephone are already registered. To register a “foreign” handset please refer to it’s user manual.
Press the MENUOK button. Select REGISTER using 
/ 
and press the MENUOK button. Using 
/ 
select a base station to subscribe to and press the MENUOK button. Enter the base’s PIN (EM6113 base station in delivery state “000”). The phone will ask “PRESS
BASE”
Press and HOLD the paging key PAGE at the base station for approximately 10 seconds. The LED “IN USE/CHARGE” will begin to flash. After this the base station will be in registration mode for one minute.
Deleting a handset
You can delete a handset from a base to allow another handset to be registered.
NOTE: You can only remove other handset in your system but you are not able to remove the handset you are using.
Press the MENUOK button. Select 
/ 
and press the MENUOK button. Press and HOLD the MUTE button for approximately 3 seconds. Enter the PIN for base station (EM6113 base station “000”). Enter the internal telephone number (1...5) of the handset you want to remove.
14
