Parameter | Description |
|
|
| Min. | Max. | Default |
No. |
|
|
|
| value | value | |
D750 | Model Code | Hart parameter | - | - | - | ||
D751 | Serial Number - Control Unit | - | - | - | |||
| Store as Final Assembly Number (FAN) |
|
|
| |||
D752 | Hardware Revision |
|
| - | - | - | |
|
|
|
|
|
|
| |
D753 | Software Revision |
|
| - | - | - | |
|
|
|
| ||||
D760 | Manufacturer’s Code |
|
| - | - | - | |
| Factory set not atlerable |
|
|
|
| ||
D761 | Unique ID |
|
|
| - | - | - |
| Hart parameter |
|
|
|
|
| |
D762 | Universal Command Revision | - | - | - | |||
| Hart parameter |
|
|
|
|
| |
D763 | Transmitter Specific Command Revision | - | - | - | |||
| Hart parameter |
|
|
|
|
| |
D764 | Preamble Bytes |
|
| - | - | - | |
| Hart parameter |
|
|
|
|
| |
D765 | Flags Hart parameter |
| - | - | - | ||
D800 | PV |
|
|
| - | - | - |
D801 | Sludge Density |
|
| - | - | - | |
D805 | % Current Output |
|
| - | - | - | |
D806 | Current output | Current is proportional to PV | - | - | - | ||
D810 | Totaliser Value |
|
| - | - | - | |
D820 | Relay Status |
|
|
| - | - | - |
D821 | Relay 1 | Resettable - Hours & Minutes | - | - | - | ||
D822 | Relay 2 | Resettable - Hours & Minutes | - | - | - | ||
D830 | Alarm report | e.g. Sensor Fault, …. | - | - | - | ||
D835 | Digital input status |
|
| - | - | - | |
D841 | Current input |
|
|
|
|
|
|
| Value of current input (mA) |
| - | - | - | ||
D844 | Temperature |
|
|
|
|
|
|
| The temperature oC within the control unit | - | - | - | |||
D850 | Attenuation @ 1MHz Attenuation | - | - | - | |||
D851 | Attenuation @ 3.3MHz | Attenuation | - | - | - | ||
D852 | Attenuation unsmoothed |
| - | - | - | ||
D853 | Signal level (Raw A/D bits) |
|
|
|
| ||
| Raw RF A/D output |
|
| - | - | - | |
D854 | Span Average @ 1MHz (dB) |
|
|
|
| ||
| Diagnostic parameter that averages the span calibrations | - | - | - | |||
D855 | Span Average @ 3.3MHz |
|
|
|
| ||
| Diagnostic parameter that averages the span calibrations | - | - | - | |||
D858 | Slope 1 |
|
|
|
|
|
|
| The value of the attenuation in dB/% @ 1MHZ |
|
|
| |||
| determined by the control unit. | - | - | - | |||
D859 | Slope 3 |
|
|
|
|
|
|
| The value of the attenuation in dB/% @ 3.3MHZ |
|
|
| |||
| determined by the control unit. | - | - | - | |||
D860 | Frequency of operation |
|
|
|
| ||
| Diagnostic of frequency(ies) being used (MHz) | - | - | - | |||
D861 | Maximum density |
|
|
|
|
| |
| The maximum density that can be measured. |
|
|
| |||
| This value is calculated from zero and span data. | - | - | - | |||
IP258
37
