Emerson KF140TZ00 owner manual Preset Memory Feature, General, Installation of Battery

2. Remove the fan motor and housing assembly from the protective plastic bag. Place the fan assembly into the upper foam pad with the top of the motor facing up.

The upper foam pad serves as a hold- er for the fan during the first stages of assembly.

Preset Memory Feature

Your remote control receiver is equipped with a preset memory feature. The receiv- er will remember the light intensity and fan speed when the light and fan are turned off from the wall switch. When the wall switch is turned back on, the lights and fan will resume operation as they were prior to the

2. Slide the four switch levers on the code switch to your choice of ON (up) or down positions. Use a ball-point pen or small screwdriver and slide the levers firmly up or down.

3. In the receiver (Figure 1), slide the four switch levers to the same positions as set in the transmitter. Make sure the

!WARNING

Turning off wall switch is not suffi- cient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. All wiring must be in accordance with National and Local codes and the ceil- ing fan must be properly grounded as

General	switch being turned off.
Your Emerson ceiling fan comes equipped	Installation of Battery
with a remote control transmitter and a

levers on both switches are in the same positions, otherwise the fan will not operate.

4. Position the battery in the transmitter

a precaution against possible electri- cal shock.

remote control receiver. This remote con- trol systems is designed to control your ceiling fan speed, airflow direction, and light intensity.

NOTE: An optional SW115 Wall Control (not supplied) may also be used with the remote control receiver supplied with your ceiling fan.

IMPORTANT

1. Remove the battery cover and install four AAA alkaline batteries (not sup- plied), oriented as shown in the diagram in the battery compartment. (Figure 1).

RECEIVER

battery compartment and replace the battery cover.

CEILING FAN

PROCEDURES

Electrical Requirements

Your new ceiling fan will require a ground- ed electrical supply line of 120 volts AC, 60 Hz, 15 amp circuit.

How to Assemble Your Ceiling Fan

1. Remove the hanger ball by loosening the setscrew in the hanger ball until the ball falls freely down the downrod (Figure 2). Remove the pin from the downrod, then remove the hanger ball. Retain the pin and hanger ball for rein- stallation in step 5.

This Owner’s Manual is divided into two sections. The first section,

REMOTE CONTROL PROCEDURES, describes how to install the four alka- line batteries (not supplied) in the remote control transmitter, and how to set the operating frequency of the transmitter and receiver. These instruc- tions must be performed prior to the installation of the ceiling fan as described in the second section,

CEILING FAN PROCEDURES.

SWITCH LEVERS

ON

1	2	3	4	CODE
				SWITCH

AAA

AAA

AAA

AAA

REMOTE

CONTROL

TRANSMITTER

BATTERY COVER

Figure 1

The outlet box must be securely anchored and capable of withstanding a load of at least 50 pounds.

!WARNING

To reduce the risk of fire, electric shock, or personal injury, mount fan to outlet box marked “Acceptable for Fan Support”, and use screws sup- plied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electri-

PIN
HANGER
BALL
DOWNROD	SETSCREW

Figure 2

2. Unscrew the two upper setscrews (Figure 3) until they clear the inside of the motor coupling. Then separate, untwist and unkink the three 80” motor leads. Route the motor lead wires

REMOTE CONTROL

PROCEDURES

General

The remote control system is designed to
separately control your ceiling fan and
light intensity. There are four push buttons
on the transmitter (HIGH, MED, LOW,
OFF) to set the fan speed and turn the fan
off. The REV push button changes the air-
flow direction of the fan blades. The UP
(uplight) and DN (downlight) push buttons
turn the lights on and off and controls the
light intensities. The red indicator light will
illuminate while any button is pressed,
indicating that the battery is good.	4

Setting Operating

Frequency of Transmitter

and Receiver

Your remote control transmitter and receiver have code switches which must be set on one of 16 possible code combi- nations. The four levers (numbered 1, 2, 3, and 4) on the switches are factory-set in the ON (up) position. Do not use this setting. Change the switch settings as follows:

1.On the remote control transmitter, locate the code switch just above the battery compartment (Figure 1).

cian if in doubt.

!WARNING

To avoid possible fire or shock, fol- low all wiring instructions carefully.

Any electrical work not described in these instructions should be done or approved by a licensed electrician.

If your fan is to replace an existing ceiling light fixture, turn electricity off at the main fuse box at this time and remove the exist- ing light fixture.

5

through the downrod. Align the clevis pin holes in the downrod with the holes in the motor coupling. Install the clevis pin and secure with the hairpin clip (Figure 3). The clevis pin must go through the holes in the motor coupling and the holes in the downrod. Be sure to push the straight leg of the hairpin clip through the hole near the end of the clevis pin until the curved portion of the hairpin clip snaps around the clevis pin. The hairpin clip must be properly installed to prevent the clevis pin from working loose. Pull up on the downrod to make sure the clevis pin is properly installed.