!WARNING
It is critical that the clevis pin in the motor coupling is properly installed and the setscrew securely tightened. Failure to verify that the pin and setscrew are properly installed (as shown in Figure 3) could result in the fan falling.
5. Reinstall the hanger ball (Figure 5) on the downrod as follows. Route the three 80” motor leads through the hanger ball and slide the hanger ball over the downrod. Position the pin through the two holes in the downrod and align the hanger ball so the pin is captured in the groove in the top of the hanger ball. Pull the hanger ball up tight against the pin and securely tighten the
FIBER WASHER (4)
FAN BLADE
BLADE FLANGE
11. Partially install two
LIGHT FITTER | LIGHT FITTER |
WHITE WIRE | |
BLACK WIRE |
|
MOTOR |
|
HAIRPIN CLIP
DOWNROD
setscrew in the hanger ball. A loose setscrew could create fan wobble.
!WARNING
It is critical that the pin in the hanger ball is properly installed and the
Figure 6
BLACK WIRE |
|
ADAPTER |
|
HOLDER | MOTOR |
| WHITE WIRE |
SETSCREW (2)
Figure 3
MOTOR
COUPLING
CLEVIS PIN
setscrew securely tightened. Failure to verify that the pin and setscrew are properly installed could result in the fan falling.
CEILING | PIN | HANGER BALL |
COVER |
8. Turn the fan motor and housing assem- | ||
bly upside down in preparation for | SCREWS (2) | |
mounting the fan blade assemblies. | Figure 8 | |
Remove and discard the three shipping | ||
retainers securing the motor hub in the | 12. Connect the white wire from the light | |
motor housing. | ||
|
3. Tighten the setscrews (Figure 3) secure-
ly while pulling up on the downrod. | SETSCREW | |
NOTE: The setscrews must be properly | DOWNROD | |
installed as described above, or fan | ||
| ||
wobble could result. |
| |
4. Make sure the grommet is properly |
| |
installed in the coupling cover, then |
| |
slide the coupling cover on the down- |
| |
rod until it rests on the motor housing. |
| |
Place the ceiling cover over the down- | Figure 5 | |
rod. Be sure that the ceiling cover and | 6. The fan comes with blue, orange, black | |
the coupling cover are both oriented | ||
and white leads that are 80” long. | ||
correctly (Figure 4). | ||
Before installing the fan, measure up | ||
CEILING COVER | ||
approximately 6 to | ||
DOWNROD |
NOTE: Take care not to scratch the fan | fitter to the white wire from the motor |
(Figure 8). Connect the black wire | |
housing when installing the blade | from the light fitter to the black wire |
assemblies. | from the motor. Make sure both con- |
9. Insert a | nectors are securely engaged. |
with lockwasher into each of the two | CAUTION: Do not pinch wires between |
recessed holes in one of the blade | the adapter/light fitter assembly and |
flanges. | the adapter holder. |
10. Position the blade flange on the motor | 13. Position the adapter/light fitter assem- |
hub so that the screws in the blade | bly on the adapter holder so that the |
flange align with the two threaded | two |
holes in the motor hub (Figure 7). | protrude through the keyhole slots in |
Tighten the two screws securely. | the adapter (Figure 9). Turn the |
Repeat this procedure for the remain- | adapter counterclockwise and then |
ing four blade assemblies. | tighten the two screws. Securely install |
of hanger ball/downrod assembly. Cut |
off excess leads and strip back insula- |
tion 1/2” from end of leads. |
BLADE FLANGE
another
| 7. Mount the fan blades to the blade | |
COUPLING | flanges using four | |
COVER | head screws and | four fiber washers |
GROMMET | (supplied) (Figure 6). |
NOTE: If necessary, grasp the light fit- ter and gently turn slightly to gain access to the screw heads.
INSTALL
Figure 4 | 6 |
!WARNING
To reduce the risk of personal injury, do not bend the blade flange when installing the blade flanges, balanc- ing the blades or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
MOTOR HUB
Figure 7
LIGHT FITTERPAN HEAD SCREW ASSEMBLY
ADAPTER
| Figure 9 | TIGHTEN TWO PAN |
7 | HEAD SCREWS | |
|
|