5.1 Analyzer Module Setup

5.1.1 Calibration Parameters – Time controlled calibration

Main Menu — Analyzer and I/O-module expert configuration

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Analyzer module setup

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Calibration parameters

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Time controlled calibration

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TAG

 

 

 

 

 

 

 

 

37.50 ppm

 

 

 

 

 

 

 

 

 

 

 

 

-- Time Control --

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Zero calibration - Day of week:

 

 

 

 

 

Never

 

 

 

 

 

 

 

 

- Hour:

 

 

 

 

 

 

 

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

- Minute:

 

 

 

 

 

 

 

0

 

 

 

 

 

 

 

 

Span calibration - Day of week:

 

 

 

 

 

Never

 

 

 

 

 

 

 

 

- Hour:

 

 

 

 

 

 

 

0

 

 

 

 

 

 

 

 

- Minute:

 

 

 

 

 

 

 

0

 

 

 

 

 

 

 

 

Zero+Span calibration - Day of week:

 

 

Never

 

 

 

 

 

 

 

 

- Hour:

 

 

 

 

 

 

 

0

 

 

 

 

 

 

 

 

- Minute:

 

 

 

 

 

 

 

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Measure

 

 

 

Channel

 

Back...

 

ShowList...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F1

F2

 

F3

 

F4

F5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

In the menu "Time Control" you can determine the starting time of the zero gas calibration resp. the span gas calibration for one channel. If you want to determine the values of the other channels of an MLT analyzer or analyzer module, press the F3 key.

Notes:

¨The time controlled calibration is only possible if the span gas comes from a valve gear! If the valve gear is not available you have to select "Never" in all lines containing "Day of week".

¨A zero gas calibration should be done before starting a span gas calibration. Therefore the starting time of the zero gas calibration should be different from the starting time of the span gas calibration. If you select the option "Zero+Span calibration" the zeroing will run before the spanning, automatically.

Set up time parameters:

¨Select any line of variables with the -key or the -key.

¨Select the variable with the 8 -key or the -key.

¨Select any digit with the -key or the -key and adjust a new value with

the -key or the -key resp. select the whole parameter with the -key or the -key. Options for day of week: Monday, ..., Sunday, Each day, Never

for hour:

0, 1, 2, 3, ..., 23

for minute:

0, 1, 2, 3, ..., 59

¨ Confirm the new value with the 8 -key or cancel and go back to the last value with F2.

5 - 12

NGA 2000

90003482(2) [NGA-e (MLT-Software 3.2.X)] 07/98