6.2.2 Service Menus

Analyzer Module Data

Main Menu — Technical level configuration

 

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Service menus

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Manufacturing data

 

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Analyzer module data

 

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CLD

 

 

 

 

 

 

 

 

 

 

95.0 ppm

 

 

 

 

 

 

 

 

 

 

 

Analyzer manufacturing data

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Analyzer module s/n:

 

 

 

 

 

 

 

CLD1

 

 

 

 

 

 

 

 

 

Manufacturing date code:

 

 

 

?

 

 

 

 

 

 

 

 

 

Bench configuration code:

 

 

CLA - low range

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Hardware revision number:

 

 

 

1.0

 

 

 

 

 

 

 

 

 

Software revision number:

 

 

 

2.3

 

 

 

 

 

 

 

 

 

Minimum range:

 

 

 

 

 

 

 

10.0 ppm

 

 

 

 

 

 

 

 

Maximum range:

 

 

 

 

 

 

10000 ppm

 

 

 

 

 

 

 

 

Diode s/n, block s/n:

 

 

 

 

 

 

0000; 0000

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Capillary:

 

 

 

 

 

 

 

 

200.0 ml/min

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HOME

 

ESCAPE

 

RESET

 

STORE

 

INFO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F1

 

F2

 

F3

 

F4

 

F5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

In the menu "Analyzer manufacturing data" you will find the hardware revision number, the software revision number and the serial number of the CLD analyzer module. Besides, you can set up some measurement parameters.

Set up parameters:

¨Select any line of variables with the ↓ -key or the − -key.

¨Select the variable with the ENTER key or the → -key.

¨Select any digit with the ← -key or the → -key and adjust a new value with the − -key or the ↓ -key.

¨Confirm the new value with the ENTER key or cancel and go back to the last value with the F2 key.

Lines of variables "Analyzer module s/n", "Manufacturing date code", "Bench configuration code" and "Diode s/n, block s/n":

The data in these lines are specific CLD analyzer module data. They were set up by the manufacturer during the first startup procedure of the module. A changing of these data will only be necessary, if hardware setups or software setups will be changed. Only specialists should change these parameters.

Note: The serial number of your CLD analyzer module you will find in the line "Analyzer module s/n". Please give this number to your customer service, if you have questions about your CLD analyzer module!

90003749(1) [NGA-e (Software CLD 2.3/MLT 3.1.X)] 04/98

NGA 2000

6 - 19