5.1.9 Analyzer Module Set up

Analyzer Parameter List

Main Menu — Expert controls and set up

 

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Analyzer module set up

 

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Analyzer Parameter List

 

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CLD

 

 

 

 

 

 

 

 

 

 

95.0 ppm

 

 

 

 

 

 

 

 

 

 

 

 

Analyzer Parameter List

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Analyzer tag:

 

 

 

 

 

 

 

CLD

 

 

 

 

 

 

 

 

 

Ozonator status:

 

 

 

OFF - PRESSURE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ozonator power:

 

 

 

 

 

 

Enabled

 

 

 

 

 

 

 

 

First line´s parameter:

 

 

 

 

Sample press.:

 

 

 

 

 

 

 

 

Second line´s parameter:

 

Detector temperature:

 

 

 

 

 

 

 

 

Third line´s parameter:

 

 

 

Block temperature:

 

 

 

 

 

 

 

 

Fourth line´s parameter:

 

 

 

 

Converter temp.:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Linearizer parameters...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HOME

 

ESCAPE

 

NEXT

 

LAST

 

INFO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F1

 

F2

F3

 

F4

 

F5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

In the menu "Analyzer Parameter List" you can set up parameters of the single component display, of the ozonator and the analyzer tag. You can also change to several submenus, where you can set up linearizer parameters, concentration and calibration parameters.

Set up parameters:

¨Select any line of variables or the menu line "Linearizer parameters..." with the ↓ -key or the − -key.

¨Select the variable or change to the submenu "Linearity coefficients" with the ENTER key or the → -key.

¨Select any digit with the ← -key or the → -key and adjust a new value with the − -key or the ↓ -key

resp. select the whole parameter with the − -key or the ↓ -key.

¨Confirm the new value with the ENTER key or cancel and go back to the last value with the F2 key.

Line of variables "Analyzer tag":

You can input a tag of maximum thirty digits. You will find the same line in the menu "Analyzer module set up" (see chapter 5.1 p. 5-3).

Caution:

Normally, you will find "CLD" as analyzer module tag in the line "analyzer tag".

If the CLD module is part of an analyzer network: You have to change the configuration of the programmable digital inputs and analog outputs, if you change the identification tag ! Because, the parameters of the module source will change ! So, the relations will disappear !

90003749(1) [NGA-e (Software CLD 2.3/MLT 3.1.X)] 04/98

NGA 2000

5 - 23