5.4.1 System Set Up

Front panel control

Main Menu — Expert controls and set up

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

System set up

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Front panel control

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CLD

 

 

 

 

 

 

 

 

95.0 ppm

 

 

 

 

 

 

 

 

 

 

 

 

Front Panel Control

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LCD brightness:

 

 

 

 

 

70 %

 

 

 

 

 

 

 

 

 

LCD viewing angle:

 

 

 

 

 

25 %

 

 

 

 

 

 

 

 

 

Beeper enable:

 

 

 

 

 

 

Off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Beeper frequency:

 

 

 

 

 

1.00 kHz

 

 

 

 

 

 

 

 

Reading refresh rate:

 

 

 

 

 

 

1 s

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Drop out of menus after:

 

 

 

10 min

 

 

 

 

 

 

 

 

Date and time...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HOME

 

ESCAPE

 

 

 

 

 

INFO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F1

 

F2

F3

F4

F5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

In the menu "Front panel control" you can set up several display parameters.

Set up parameters:

¨Select any line of variables or the menu line with the ↓ -key or the − -key.

¨Select the variable with the ENTER key or the → -key.

¨Select any digit with the ← -key or the → -key and adjust a new value with the − -key or the ↓ -key

resp. select the whole parameter with the − -key or the ↓ -key.

¨Confirm the new value with the ENTER key or cancel and go back to the last value with the F2 key.

Lines of variables "LCD brightness" and "LCD viewing angle":

In these two lines you can determine the quality of the LCD reproduction. The best values depend on your position to the screen and on the light of the environment.

¨Options: 20 to 100% for LCD brightness and 10 to 80% for LCD viewing angle.

¨Usually: 70 to 90% (brightness) and 20 to 30% (angle).

¨Caution: Be careful with the changing of these values! Perhaps you can not read the display any longer if you use very extreme values! It is not possible to load standard values via keyboard!

Lines of variables "Beeper enable" and "Beeper frequency":

The functionality of these two lines is not available at the moment!

5 - 48

NGA 2000

90003749(1) [NGA-e (Software CLD 2.3/MLT 3.1.X)] 04/98