Line of variables "Reading refresh rate":

In this line you can determine how often the display shall be built up in a certain time interval. Options: 1s to 60s. Standard: 1s.

Line of variables "Drop out of menus after":

In this line you can decide if and after which time without front panel operations the display shall change from the current menu to the single component display.

¨Options: 10s, 30s, 1min, 5min, 10min, 30min, Never.

Date and time set up:

Press the ENTER key or the → -key in the line "Date and time..." to change to the corresponding submenu:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CLD

 

 

 

 

 

 

 

 

 

 

 

95.0 ppm

 

 

 

 

 

 

 

 

 

 

 

 

 

Date and Time

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Time display format (am/pm):

 

 

 

 

 

24 Hrs

 

 

 

 

 

 

 

 

Network updating:

 

 

 

 

 

 

 

 

Enabled

 

 

 

 

 

 

 

 

 

Minutes:

 

 

 

 

 

 

 

 

 

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Hours:

 

 

 

 

 

 

 

 

 

12

 

 

 

 

 

 

 

 

 

(Entered as 24Hrs format)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Day:

 

 

 

 

 

 

 

 

 

21

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Month:

 

 

 

 

 

 

 

 

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Year:

 

 

 

 

 

 

 

 

 

1998

 

 

 

 

 

 

 

 

 

Current time:

 

 

 

13:48:20

21 Feb 1998

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HOME

 

ESCAPE

 

 

 

 

SET

 

 

INFO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F1

 

F2

F3

 

F4

 

 

F5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

In the menu "Date and Time" you can set up the date and the time of the control module (platform or MLT analyzer).

Line of variables "Time display format (am/pm)":

In this line you can decide if the time of the control module should be displayed in the 12 hours format or in the 24 hours format.

Line of variables "Network updating":

Select "Enabled" if you want that all modules combined with the platform or the MLT analyzer can use the date and time setup of the control module. Else, select "Disabled".

Set up a new date or time:

1)Press the ENTER key or the → -key in the line "Minutes", "Hours", "Day", "Month" or "Year" to select the corresponding number.

2)Select any digit with the ← -key or the → -key and adjust a new value with the − -key or

the ↓ -key.

¨Options: Minutes: 0 to 59, Hours: 0 to 23, Day: 1 to 28/30/31 depending on the month

selected, Month: 1 to 12, Year: 1996 to 2035.

3)Press the F4 key to set the new date or time. The new adjustment will appear in the line "Current time". The display in this line will be refreshed every five second.

90003749(1) [NGA-e (Software CLD 2.3/MLT 3.1.X)] 04/98

NGA 2000

5 - 49