5.4.3 System Set Up

Auxiliary Lines

Main Menu — Expert controls and set up

 

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

System set up

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Auxiliary lines

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CLD

 

 

 

 

 

 

 

 

 

95.0 ppm

 

 

 

 

 

 

 

 

 

 

 

 

 

Auxiliary lines

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

First auxiliary line:

 

 

 

 

 

 

Enabled

 

 

 

 

 

 

 

 

 

Second auxiliary line:

 

 

 

 

 

 

Enabled

 

 

 

 

 

 

 

 

 

Third auxiliary line:

 

 

 

 

 

 

Enabled

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fourth auxiliary line:

 

 

 

 

 

 

Enabled

 

 

 

 

 

 

 

 

First line source...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Second line source...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Third line source...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Last line source...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HOME

 

ESCAPE

 

NEXT

 

 

 

INFO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F1

 

F2

 

F3

F4

F5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

In the menu "Auxiliary lines" you can determine if the last four lines in the single component display of the current channel shall appear. If you want to set up the lines of the other channels of the joint analyzer modules, press the F3 key.

Set up parameters:

¨Select any line of variables or any menu line with the ↓ -key or the − -key.

¨Select the parameter with the ENTER key or the → -key.

¨Select "Enabled" or "Disabled" with the − -key or the ↓ -key to enable or disable the display of the corresponding auxiliary line in the single component display.

¨Confirm the parameter selected with the ENTER key or cancel and go back to the last adjustment with the F2 key.

Choose the source module for the auxiliary lines:

Press the ENTER key or the → -key in the line "First line source...", "Second line source...", "Third line source..." or "Last line source..." to change to the corresponding submenu. The tags of all modules combined with the platform or the MLT analyzer are available:

90003749(1) [NGA-e (Software CLD 2.3/MLT 3.1.X)] 04/98

NGA 2000

5 - 51