GENERAL INSTRUCTIONS

Follow a few simple rules and your Empire furnace will give you years of trouble-free heating. When your furnace is ready for installation, operation or repair here are a few DO's and DON'T's.

DON'T install the furnace yourself if you are not qualified in working with gas piping, chimneys, flue pipes, and venting. Gas appliances and gas piping should be installed or repaired only by a qualified serviceman.

DO get a qualified installing agency to install your furnace. By the term "qualified installing agency" is meant any individual, firm, corporation or company which either in person or through a representative is engaged in and is responsible for the installation or replacement of gas piping on the outlet side of the meter, or of the service regulator when a meter is not provided; or the connection, installation or repair of gas appliances, who is experienced in such work, familiar with all precautions required; and has complied with all the requirements of the authority having jurisdiction.

The installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code ANSI Z223.1.

*Available from the American National Standards Institute, Inc., 11 West 42nd

St., New York, N.Y. 10036.

DO consult your dealer and local gas supplier about qualified installers and servicemen.

DO refer to your Empire Installer and Serviceman's Manual so that you can make sure that all installation and service work was done properly. You bought the best furnace, now make sure you get the best service.

DO make sure your venting system and flue pipe were installed as outlined in your Empire Installer and Serviceman's Manual.

DO see "Using Your Furnace" before you try to light the pilot or turn your furnace on.

DO see "Using Your Furnace" for instructions on how to set the register temperature control when children are present.

CAUTION

Floor register becomes hot when operating and can cause burns. Keep children off!

DON'T adjust or repair the combination valve, and don't take it apart.

DON'T try to make any repairs except the ones listed for you to do in Service Checks.

DID YOU GET EVERYTHING?

After you have unpacked your Empire furnace, you should make certain everything is in order. For example, did you receive the model furnace you ordered? Is it the model for the type of gas (Natural or Propane) you want? Did you get all of the parts you are supposed to have? Look at picture A. It will tell you where your furnace identification plate is. The plate has stamped on it the model and serial number of the furnace you received. It also tells if your furnace is supposed to use natural (NAT) or propane (LP) gas. See if the serial number on your furnace is the same as the number on the WARRANTY CARD. Be sure your dealer fills out the WARRANTY CARD, then MAIL the purchaser's report

(bottom part) to us. Look at Picture A and also the list below to see if you have received everything on the list. If anything is missing or broken, or if the model or serial numbers are not right, or if the furnace is for natural and you have propane (or the other way around), contact your dealer or Empire Comfort Systems, Inc.

A

1.Owner's manual (you are reading it now)

2.Installer and Serviceman's Manual

3.Wall thermostat (packed in draft diverter carton)

4.Draft diverter (packed in separate carton)

5.Cardboard cutout template (inside top of furnace box)

6.Register (top of furnace)

7.Warranty card

8.Debris pan

9.Lighting rod (inside furnace lying on bottom)

10.Inner casing (inside furnace)

HOW YOUR FURNACE WORKS

HEATING

Your Empire furnace uses air from two places; air from outside the living area, and air from inside the living area. The air from outside the living area is mixed with gas and burned inside a chamber in your furnace. The burned gas and air is exhausted through a flue pipe to the outside air again. This exhaust should not be permitted to enter the living area.

Burning gas inside the furnace chamber makes the chamber hot. Cool air from inside the living area is drawn into the furnace and flows past the outside of the hot chamber. The chamber makes this air hot and this hot air flows out of the furnace and back into the living area. When enough air in the living area has been heated, the thermostat turns the furnace off automatically.

Picture B shows the flow of air inside and air outside the living area. You can see that the air inside is not mixed with air outside the living area. The furnace does not burn air that is within your living area, and burned air or exhaust should not enter the living area.

Page 4

R-1842

Page 3 Page 5
Page 4
Image 4
Empire Comfort Systems 7088-3, 3588-3 General Instructions, HOW Your Furnace Works, Did YOU GET EVERYTHING?, Heating
Page 3 Page 5

5088-3, 7088-3, 3588-3 specifications

Empire Comfort Systems offers a reliable range of heating solutions, with the models 5088-3, 7088-3, and 3588-3 standing out for their exceptional performance and innovative features. These gas-fired wall heaters are designed to provide efficient heat while maintaining user-friendly operations and stylish aesthetics.

One of the key features of the Empire Comfort Systems 5088-3 is its compact design, allowing it to fit snugly into smaller spaces without sacrificing heating capability. It boasts a powerful capacity to heat areas swiftly and effectively, making it ideal for both residential and commercial applications. The heater utilizes natural gas or propane, ensuring flexibility in fuel preference and availability.

The 7088-3 model expands upon this with additional features, including a built-in thermostat that allows for precise temperature control. This thermostat enables users to set their desired heat levels, ensuring optimal comfort without unnecessary energy expenditure. Another significant characteristic of the 7088-3 is its safety features, which include an automatic shut-off system that kicks in during abnormal conditions, providing peace of mind for users.

The 3588-3 model emphasizes efficiency, featuring advanced technologies that maximize heat output while minimizing fuel consumption. With a sleek design available in various finishes, it can seamlessly integrate into any home or office decor. The 3588-3 also prioritizes safety, equipped with a reliable ignition system that enhances operational security.

All three models feature Empire's proprietary Heating Technology, designed to distribute warmth evenly across the space, eliminating cold spots and ensuring consistent comfort. Additionally, they operate quietly, making them perfect for bedrooms, living rooms, or office environments where noise levels are a concern.

Whether you are looking for efficient heating solutions for your home or business, the Empire Comfort Systems models 5088-3, 7088-3, and 3588-3 each offer unique advantages. Their combination of advanced technology, safety features, and stylish designs positions them as leading choices in the market for reliable and effective heating solutions. With Empire Comfort Systems, achieving warmth and comfort becomes an effortless experience.
Top Page Image Contents