Manuals / Enerco / Household Appliance / Gas Heater

Enerco MHBF10NG, TSIR20NGT, TSBF10NG, MHBF6NG, MHIR20NGT Fastening Heater to Wall, Mounting Bracket

Models: MHBF10NG HSIR20NGT HSBF10NG MHIR10NG MHIR20NGT MHBF6NG TSIR20NGT TSBF10NG TSIR10NG HSIR10NG

1 24
Download 24 pages 14.57 Kb
Page 6
Image 6

 

36” min. from

6” Min from

ceiling

 

 

adjoining

 

 

walls

 

 

 

 

 

Left

SideRight

Side

Floor

2” min. to top surface of carpet, tile or other combustible material

Figure 4

FASTENING HEATER TO WALL

Mounting Bracket

The mounting bracket in located on the back panel of heater (see figure 5). It has been taped there for ship- ping. Remove mounting bracket from back panel.

Mounting

Bracket

Figure 5

Removing Front Panel of Heater

1.Remove three screws on bottom front of front panel.

2.Pull bottom of front panel forward, then down (see figure 6)

Figure 6

Attaching Mounting Bracket to Wall

Use holes on each end of mounting bracket to attach bracket to wall. These holes are 16 inches apart. Attach mounting bracket to wall in one of two following ways.

1.Attach to wall studs

2.Attach to wall anchor

Attaching to Wall Stud:

This way is the best providing the strongest mounting in wood frame houses.

Attaching to Wall Anchor:

This way allows you to attach mounting bracket to hol- low walls (wall areas between studs) or to solid walls (concrete or masonry).

Decide which way best suits your needs. Either method will provide a secure hold for the mounting bracket.

1.Tape mounting bracket to wall where heater will be located. Make sure mounting bracket is level. For wall stud mounting locate one end of the mounting bracket over a wall stud.

WARNING: Maintain minimum clearances shown in figure 7. If you can, provide greater clearances from the floor and joining wall.­

2.Mark screw locations on wall (see figure 7).

3.Remove tape and mount bracket from wall.

6-1/2” Min. 10,000 BTU 10-1/4” min 20,000-30,000 BTU

Wall

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Adjoining

 

16” (Lg)

 

 

 

 

 

 

 

 

12-9/64” (Sm)

 

 

 

 

 

 

 

 

 

 

17-1/2” Min.

 

 

 

 

 

Mark mounting hole locations

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

and drill holes where indicated.

 

 

 

 

 

 

 

Allow for minimum clearances

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 7

Attaching to Wall Stud:

For attaching mounting bracket to wall studs

1.Drill holes at marked locations using 9/64” drill bit.

2.Place mounting bracket onto wall. Line up holes on each end of bracket with hole drilled in wall.

3.Insert mounting screws through bracket and into wall studs.

4.Tighten screws until mounting bracket is firmly fastened to wall studs.

Attaching to Wall using Anchor:

For attaching mounting bracket to hollow walls (wall ar- eas between studs) or solid walls (concrete or masonry)

Note: Wall anchors, mounting screws, and spacer are in hardware package. The hardware package is provided with heater.

Unvented Natural Gas Fired Room Heater

6

Installation Instructions and Owner’s Manual

Page 5 Page 7
Page 6
Image 6
Enerco MHBF10NG, TSIR20NGT, TSBF10NG, MHBF6NG, MHIR20NGT, HSIR20NGT, HSIR10NG Fastening Heater to Wall, Mounting Bracket
Page 5 Page 7

MHBF10NG, HSIR20NGT, HSBF10NG, MHIR10NG, MHIR20NGT specifications

The Enerco HSIR10NG, TSIR10NG, TSBF10NG, TSIR20NGT, and MHBF6NG are a line of innovative heating solutions designed to meet various heating needs in both residential and commercial applications. Each model is engineered with advanced technologies and features that prioritize efficiency, performance, and user convenience.

The HSIR10NG is a high-efficiency infrared heater that operates on natural gas. It provides powerful heating with minimal energy consumption, utilizing infrared technology to warm objects and people directly rather than just the surrounding air. This results in faster heating and lower energy costs, making it an ideal choice for garages, workshops, or outdoor spaces.

Following closely is the TSIR10NG, another natural gas infrared heater known for its compact design and efficiency. This model features a state-of-the-art burner design that maximizes heat output while ensuring low emissions. The TSIR10NG is particularly suited for smaller spaces, providing targeted heating where it is needed most. It can easily be mounted on walls or ceilings, offering versatility in installation options.

The TSBF10NG is a dual-fuel infrared heater, allowing users to switch between natural gas and propane as needed. This flexibility makes it suitable for various environments and user preferences. The heater's robust construction ensures durability, while its adjustable heating levels allow for customized comfort.

For larger areas, the TSIR20NGT offers an enhanced heating capacity with similar infrared technology. This model is ideal for industrial or commercial spaces requiring efficient heating. With its advanced thermostat controls, users can maintain a consistent temperature while benefiting from lower operational costs.

Lastly, the MHBF6NG is a portable heating solution designed for versatility and convenience. This compact model is perfect for temporary heating needs, featuring an easy-to-use design that allows for quick setup and relocation. Its propane compatibility makes it a popular choice for outdoor events, workshops, or emergency heating situations.

Each model is equipped with advanced safety features, including automatic shutoff mechanisms and durable heat-resistant materials, ensuring peace of mind during operation. The Enerco line is engineered not only for performance but also for ease of maintenance, making them reliable options for users seeking efficient heating solutions. Overall, Enerco's HSIR10NG, TSIR10NG, TSBF10NG, TSIR20NGT, and MHBF6NG provide a range of effective heating options tailored to diverse environments and user needs, combining innovation with practical functionality.