Initial Installation

QUALIFIED INSTALLERS ONLY

GAS LINE CONNECTION AND TESTING:

WARNING: Only persons licensed to work with gas piping may make the necessary gas connections to

this appliance.

 

 

Manifold

Inlet

GAS LINE CONNECTION

Pressure Tap

Pressure Tap

This stove is equipped with a certified flexible pipe

located on the right side of the unit terminating in a 3⁄8”

male NPT fitting. Consult your local authorities codes or

the CAN/CGA B 149 (1 or 2) installation code in Canada,

or in the USA gas installations follow either local codes

or the current edition of the National Fuel Gas Code ANSI

Z223.1.

The efficiency rating of this appliance is a product

TP TH

 

TP

 

TH

 

T

P

I

OL

 

OUT

H

O

L

I

 

IN

 

OF

 

F

 

P

I

L

T

O

NO

 

of the thermal efficiency rating determined under

continuous operating conditions and

was determined

independently of any installed system.

 

Pilot Adjustment

Hi/Low

Gas Control

Screw

Knob

Knob

Figure 33: Fully Labeled Gas Valve.

The appliance and its shutoff valves must be disconnected from the gas supply piping system during any pressure testing where the pressure exceeds 1⁄2 PSIG (3.45 KPa) or damage will occur to the valve.

The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1⁄2 psig (3.45 KPa).

Always check for gas leaks with a soap and water solution after completing the required pressure test.

TO TEST VALVE PRESSURES

The pressure taps are located on the left side of the valve

Turn set screw 1 turn counter clockwise to loosen,

Place 5/16” (8 mm) I.D. hose over pressure tap system.

Check pressures using a manometer.

When finished, release pressure, remove hose & tighten set screw.

Table 8: Pressure and BTU Information.

 

Natural Gas

Propane

 

 

 

Main Burner

PO512-42 DMS

PO512-54

 

 

 

Manifold Pressure

3.8” W.C. / 0.95KPa

11.0” W.C. / 2.7KPa

 

 

 

Min. Manifold Pressure

1.1” W.C. / 0.27KPa

2.9” W.C. / 0.72KPa

 

 

 

Max Supply Pressure

7.0” W.C. / 1.74KPa

13.0” W.C. / 3.28KPa

 

 

 

Min. Supply Pressure

5” W.C. / 1.24KPa

12.0” W.C. / 2.98KPa

Max BTU/hr Input

26,000 BTU/hr (7.62 KW)

26,000 BTU/hr (7.62 KW)

Min. BTU/hr Input

15,000 BTU/hr (4.4 KW)

14,000 BTU/hr (4.1 KW)

 

 

 

Venturi Setting

1⁄4” (6mm) minimum

Completely Open

 

 

 

NEVER USE AN OPEN FLAME FOR LEAK TESTING.

20

Page 20
Image 20
Enviro 50-1628 Natural Gas Propane Main Burner, Min. Manifold Pressure, Max Supply Pressure, Min. Supply Pressure

50-1628 specifications

Enviro 50-1628 is a revolutionary piece of technology designed to enhance sustainability and efficiency in various applications, particularly in the field of environmental management. This advanced system focuses on achieving ecological balance while delivering high performance, making it a valuable asset for industries aiming for greener operations.

One of the main features of the Enviro 50-1628 is its cutting-edge filtration technology. The system utilizes multi-stage filtering mechanisms that purify air and water, effectively removing pollutants and contaminants. This is accomplished through a combination of mechanical, chemical, and biological processes, ensuring that the output meets or exceeds regulatory standards. The efficiency of the filtration system plays a crucial role in reducing environmental impact by minimizing harmful emissions and discharges.

Another notable characteristic of the Enviro 50-1628 is its intelligent monitoring capabilities. Equipped with advanced sensors, the system continuously collects data on environmental parameters such as air quality, temperature, and humidity. This real-time data is processed through sophisticated algorithms, enabling proactive adjustments to optimize system performance. This not only improves the efficiency of operations but also allows for timely interventions to prevent potential environmental hazards.

In terms of energy efficiency, the Enviro 50-1628 is designed with sustainability in mind. It incorporates renewable energy sources, such as solar panels, to power its systems, significantly reducing dependency on fossil fuels. Moreover, its modular design allows for easy scalability, enabling facilities to expand their capacity while maintaining energy efficiency and reducing carbon footprints.

The Enviro 50-1628 is also user-friendly, featuring an intuitive interface that allows operators to easily monitor and control various functions. This accessibility is crucial for promoting best practices in environmental management, ensuring that organizations can effectively implement and adhere to sustainability initiatives.

Furthermore, the Enviro 50-1628 is built with durability in mind, utilizing high-quality materials to ensure long-lasting performance even in demanding environments. This resilience not only extends the lifespan of the system but also reduces maintenance costs, making it a cost-effective solution for businesses committed to sustainable practices.

In summary, the Enviro 50-1628 stands out as a powerful tool in the pursuit of environmental sustainability. Its advanced filtration technology, intelligent monitoring systems, energy efficiency, user-friendly interface, and durable construction make it an excellent choice for industries looking to minimize their ecological footprint while maximizing operational efficiency. By integrating such technologies, organizations can take significant strides towards a greener future.