Initial Installation

AUTOMATIC SAFETY SHUT DOWN:

If the spill switch is activated and shuts off the main burner the following procedure should be followed.

•Is the pilot flame still on? If not, the reason for the fireplace shut down is not the spill switch.

•Turn off the pilot flame and turn off all controls. Let fireplace to cool down. Refer to Owner’s Manual.

•Check for blockages or restrictions in the flue and venting components.

•Restart the fireplace and check for vent draft as described earlier.

•Operate the fireplace in a normal manner.

•If the main burner shuts down again after a period of operation, turn off the fireplace and contact your service technician.

SPILL SWITCH REPLACEMENT:

Use the following instructions to replace the Safety Spill Switch.

1.Turn the unit off and allow it to cool.

2.Disconnect the spill switch wires from the valve and on/off/remote rocker switch wire (see Figure 39).

3.Remove the four mounting screws holding the spill switch bracket and remove the bracket (see Figure 43).

4.Remove and replace the spill switch with a 50-885 Spill Switch Assembly using a T-20 torx type driver.

5.Follow the reverse of the previous steps.

OPTIONAL FINISHING:

Figure 43: Spill switch installation.

In installations where the flue connector is running from the drafthood into a non-combustible chimney the following optional finishing technique can be used.

CAUTION: Installations where the flue connector or venting connects to, or passes through, combustible walls or ceilings, the inner vent components must be ‘B-vent’. It is not allowable in these applications to use single wall inner vent components.

For decorative purposes a 6” (15 cm) single wall black stove pipe may be installed over the 4” (10 cm) single wall or ‘B-Vent’.

Note: The use of these components is for aesthetic purposes only and does not effect the fact that the fireplace, when fitted with the Drafthood Adaptor, is a Natural Vent appliance and therefore draws air in through the Drafthood Adaptor intake ports.

27

Page 26 Page 28
Page 27
Image 27
Enviro Ascot owner manual Automatic Safety Shut Down, Spill Switch Replacement, Optional Finishing
Page 26 Page 28

Ascot specifications

Enviro Ascot is a cutting-edge innovation in sustainable living, a forward-thinking development that marries modern architecture with eco-friendly technologies. Nestled in a prime location, Enviro Ascot is designed to minimize environmental impact while maximizing the quality of life for its residents. The project stands as a testament to how urban spaces can be designed sustainably without compromising on aesthetics or functionality.

One of the main features of Enviro Ascot is its emphasis on energy efficiency. The buildings are equipped with state-of-the-art insulation materials and energy-efficient windows that help to reduce heat loss in winter and heat gain in summer. Solar panels placed on rooftops harness renewable energy, providing a significant portion of the electricity needs for the community. This not only lowers utility costs but also significantly reduces the carbon footprint of the development.

Water conservation is another hallmark of Enviro Ascot. The community features a rainwater harvesting system that collects and stores rainwater for use in irrigation and other non-potable applications. This initiative not only conserves precious water resources but also alleviates pressure on local water supply systems. Additionally, drought-resistant landscaping has been incorporated into the design, ensuring that the green spaces remain vibrant even during dry spells.

In terms of transportation, Enviro Ascot promotes a car-free lifestyle with extensive biking and walking paths interwoven throughout the community. Charging stations for electric vehicles are available at strategic locations, encouraging the use of eco-friendly transportation. The design is pedestrian-centric, making it easy for residents to access essential services, parks, and amenities without the need for a car.

Furthermore, the community boasts smart home technologies that enhance convenience and sustainability. Homes are outfitted with smart thermostats, energy-monitoring systems, and home automation features, allowing residents to optimize their energy use seamlessly. Through a centralized app, residents can monitor energy consumption, schedule heating and cooling, and even control lighting and security systems from their smartphones.

The architectural design of Enviro Ascot reflects a contemporary aesthetic while being practical. Natural materials and earthy color palettes integrate the buildings into the surrounding environment, creating a harmonious blend with nature. Green roofs and living walls add to the biodiversity of the area, providing habitats for various species and improving air quality.

In conclusion, Enviro Ascot is not just a residential development; it is a vision for the future of sustainable living. With its commitment to energy efficiency, water conservation, and innovative technologies, it stands as a model for environmentally responsible urban design. Residents of Enviro Ascot enjoy a lifestyle that is both modern and eco-conscious, paving the way for a sustainable future.
Top Page Image Contents