Installation

THROUGH WALL INSTALLATION:

The MERIDIAN can be vented through the wall using two different methods. Only use vent of (L or PL) type with an inside diameter of 3 or 4 inches (7.6 or 10.1 cm)

VENT INSTALLATION: INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER.

A chimney connector shall not pass through an attic or roof space, closet or similar concealed spaces, or a floor, or ceiling. Where passage through a wall, or partition of combustible construction is desired, the installation shall conform to CAN/CSA-B365, Installation Code for Solid-Fuel-Burning Appliances and Equipment.

STRAIGHT THROUGH THE WALL.

1.Choose a location for your stove that meets the requirements stated in this manual and allows installation with the least amount of interference to house framing, plumbing, wiring, etc.

2.Place the appliance 15” (37.5 cm) away from the wall. If the stove is to be set on a hearth pad, set the unit on it.

3.Locate the center of the exhaust pipe on the stove. Extend that line to the wall. Once you have located the center point on the wall, use a hole saw to cut a 10” (254 mm) diameter hole for a 3” (76 mm) vent pipe or an 11” (279 mm) hole for a 4” (101 mm) vent pipe.

4.Install the wall thimble as per the instructions written on the thimble. Maintain an effective vapour barrier in accordance with local building codes.

5.Install a length of 3” (76 mm) or 4” (101 mm) vent pipe into the wall thimble. The pipe should install easily into the thimble.

6.Install the fresh air intake.

7.Connect the exhaust vent pipe to the exhaust pipe on the stove. Seal all connections with high temperature silicone

8.Push the stove straight back, leaving a minimum of 3” (7.6 cm) clearance from the back of the stove to the wall. Seal the vent pipe to the thimble with high temperature silicone.

9.The pipe must extend at least 12” (30 cm) away from the building. If necessary, bring another length of pipe (PL type) to the outside of the home to connect to the first section. Do not forget to place high temperature silicone around the pipe that passes through the thimble.

10.Install a vertical pipe, or if all requirements for direct venting are met, install vent termination. The stainless steel cap termination manufactured by the vent manufacturer is recommended. However, when the vent terminates several feet above ground level and there are no trees, plants, etc. within several feet, a 45° elbow with rodent screen can be used as a termination. The elbow must be turned down to prevent rain from entering.

NOTE:

• Some horizontal through wall installations may require a “T” and a 3 to 5 foot (91- 152cm) of vertical pipe outside the building to help natural draft in the unit.

•This may be required if a proper burn cannot be maintained, after the stove has

been tested and the airflow set.

•This is due to the backpressure in the exhaust caused by airflow around the structure.

•All sections of pipe must have three (3) screws evenly spaced and all horizontal vent sections must have a bead of high temperature silicone installed on the male end of the pipe before installation to create

a gastight seal.

Fresh Air Intake

Exhaust Tube

3" (75mm) or 4" (100mm)

"PL" or "L" vent Wall Thimble

45 deg Elbow

w/screen or

Termination Cap

High Temperature RTV

Silicone Required

17

Page 16 Page 18
Page 17
Image 17
Enviro C-10135 owner manual Through Wall Installation, Straight Through the Wall
Page 16 Page 18

C-10135 specifications

Enviro C-10135 is a cutting-edge solution that has emerged to address the growing concerns in environmental management and sustainability. Designed to meet the demands of modern industries, it incorporates a wide array of features and technologies that set it apart in the field.

One of the standout characteristics of Enviro C-10135 is its innovative waste management capabilities. The system employs advanced sorting and recycling technologies that enable efficient separation of contaminants from recyclable materials. This not only streamlines the recycling process but also significantly reduces the volume of waste sent to landfills. With a focus on circular economy principles, Enviro C-10135 helps industries adopt more sustainable practices while minimizing their environmental footprint.

The technology behind Enviro C-10135 is grounded in real-time data analytics. Integrated sensors monitor environmental conditions and waste composition continuously. This data is processed using advanced algorithms that provide actionable insights for waste management strategies. As a result, users can optimize operational efficiency, reduce costs, and enhance compliance with regulatory requirements.

Another key feature of Enviro C-10135 is its adaptability. The system can be customized to fit the specific needs of various industries, ranging from manufacturing to hospitality. Manufacturers can modify its settings to handle different types of waste, while facilities in the hospitality sector benefit from tailored solutions for food waste and packaging materials. This versatility makes Enviro C-10135 an attractive choice for businesses of all sizes.

Energy efficiency is also a salient characteristic of the Enviro C-10135. The system is engineered to minimize power consumption without compromising performance. It employs energy recovery technologies that harness excess energy generated during waste processing, which can be redirected for operational needs. This aspect not only lowers operational costs but also contributes to sustainability goals.

In addition to its technological prowess, Enviro C-10135 is user-friendly. The interface is designed to provide intuitive navigation for operators, easing the learning curve and ensuring efficient operation. Training programs and support are also available to assist users in maximizing the system's potential.

In summary, Enviro C-10135 is at the forefront of environmental technology, offering advanced waste management features, real-time monitoring and analytics, adaptability for various applications, energy efficiency, and user-friendly operation. As industries strive to meet sustainability targets, Enviro C-10135 stands as a vital asset in achieving these goals and fostering a cleaner, more sustainable future.
Top Page Image Contents