Operating Instructions

SPECIAL NOTES:

Pellet quality is a major factor in how the pellet stove will operate. If the pellets have a high moisture content or ash content the fire will be less efficient and has a higher possibility of the fire building up and creating clinkers (hard ash build-up). If this happens, pull the Slider / Damper out slightly to increase the air flow to the fire.

CONTROL BOARD FUNCTIONS:

 

 

 

 

1. AUGER TRIM: Used to change feed rates on LOW ONLY for poorer quality fuels. Push the Auger Trim

button until the number 1 and 5 lights appear on the Heat Level Indicator. This will increase the feed

rate to four (4) seconds ON time per Auger pulse. This is done only on LOW to allow the burning of

poor quality fuels. Push the button until the number 1 and 4 lights appear, this will reduce the Auger On

time to two (2) second. This setting is for high-grade fuel only. Push the button until just the number

1 light is on, this is for a three (3) second on time (standard setting).

 

 

2. AUGER PULSE LIGHT: This light will flash in conjunction with the auger.

 

 

 

 

3. MANUAL AUGER FEED: If the unit runs out of fuel, this

 

 

button can be used to “prime the auger system”. This button

 

 

will turn off after 60 seconds and then must be released and

 

1

pressed again.

 

 

 

4. SYSTEM LIGHT: Responsible for signaling the state of the

 

 

 

 

control board. When the light is flashing during start-up, the

 

 

stove is in an automatic start mode. When the light is solid,

 

 

the Heat Level Setting can be altered.

 

 

�

2

5. ON/OFF BUTTON: Used to turn the unit ON and OFF.

 

MANUAL FEED

6. HEAT OUTPUT INDICATOR: Shows

the present

heat

 

3

output setting.

 

 

 

 

 

 

4

7. HEAT LEVEL ADJUSTMENT: When

pressed, the

heat

ON/OFF

output setting of the unit will change from low to high.

 

 

Notes:

 

 

7

5

 

 

HEAT LEVEL

 

• The convection blower speed will vary automatically with the

 

 

feed rate.

 

 

 

 

• Due to varying fuel qualities this pellet stove may not operate

 

 

on lower Heat Level settings. If your unit goes out when on a

 

 

low setting move the heat level up to a higher setting.

 

Figure 2: Circuit Board Control Panel Decal. • The lowest and highest heat levels on this pellet stove are

 

 

 

 

used for adjusting and accommodating

 

Auger Trim

Auger Trim

Auger Trim

for different pellet sizes and the varying

 

energy produced by the fuels. The size

 

 

 

 

 

 

5

 

of the pellets will change the volume of

4

2 Seconds

3 Seconds

4 Seconds

fuel being fed.

 

"ON"

 

 

"ON"

"ON"

• The unit should be run at a setting

 

Factory Setting

 

 

 

1

1

1

 

where the least amount of cleaning of

 

the burn pot is needed.

 

 

 

 

Figure 3: Auger trim and heat level indicator.

7

Page 6 Page 8
Page 7
Image 7
Enviro Empress, C-10804 owner manual Special Notes, Heat Output Indicator Shows, Heat Level Adjustment When
Page 6 Page 8

C-10804, Empress specifications

Enviro Empress, model C-10804, is a cutting-edge integrated environmental management system designed to address the pressing needs of modern sustainability practices. This innovative solution combines advanced technologies to promote eco-friendly operations across various sectors, including agriculture, manufacturing, and urban planning.

One of the main features of the Enviro Empress C-10804 is its comprehensive data analytics capability. By utilizing machine learning algorithms and big data, it collects and analyzes real-time environmental data, allowing users to make informed decisions about resource allocation and waste management. This feature not only minimizes environmental impact but also enhances operational efficiency.

The C-10804 incorporates smart sensor technology, which monitors air and water quality, soil health, and energy consumption. These sensors provide continuous data streams, enabling users to identify potential issues before they escalate. For instance, if air quality drops below acceptable levels, the system can automatically activate air purification measures, ensuring compliance with environmental standards.

Another characteristic of the Enviro Empress is its modular design, allowing for easy scalability and integration into existing systems. This flexibility makes it suitable for small businesses and large enterprises alike. Companies can start with essential features and gradually expand their system as their environmental management needs evolve.

In addition, the C-10804 includes an intuitive user interface, which facilitates easy navigation and data interpretation. Users can visualize their data through customizable dashboards, enabling them to track progress toward sustainability goals efficiently. This feature empowers stakeholders at all levels to engage with environmental initiatives and fosters a culture of accountability within organizations.

Moreover, the Enviro Empress C-10804 supports renewable energy integration, making it easier for users to transition to sustainable power sources. By monitoring energy consumption patterns, the system can identify opportunities for solar or wind energy utilization, contributing to overall carbon footprint reduction.

Overall, Enviro Empress C-10804 is a powerful tool for organizations looking to enhance their environmental performance. With its advanced technologies, data-driven insights, and user-friendly features, it stands as a pivotal solution in the pursuit of sustainability and responsible resource management. As businesses increasingly prioritize environmental stewardship, the Enviro Empress will play a crucial role in shaping a greener future.
Top Page Image Contents