Operating Instructions

OPERATING YOUR PELLET STOVE:

PRE-BURN INSTRUCTIONS: The burn pot liner holes must be clear and the liner installed correctly against the ignitor tube for proper operation. Check the hopper for enough pellets to start the unit.

DO NOT OPERATE THE UNIT WITH THE DOOR OR ASH PAN OPEN.

MANUAL MODE:

To START: Press the ON / OFF button. The stove will turn on. The system light will flash. The Auger Light will flash with each pulse of the auger (the Auger Feed Rate is pre-programmed during start-up). The Heat Level Indicator will show the Heat Level that the stove will run at after start-up.

If this is the first time the unit has been started or the unit has run out of fuel, the auger will need to be primed. Press the Manual Auger Feed button until fuel starts to drop into the Burn Pot Liner (see

“OPERATING INSTRUCTIONS - CONTROL BOARD FUNCTIONS”).

To OPERATE: When a fire has been established, the System Light will turn solid (after approximately 10

-15 minutes) and the Auger Light will continue to flash to the corresponding Heat Level setting. The Heat Level button can now be pressed at this time to change the desired Heat Level Output setting.

The convection blower (room air blower) will turn on. The speed of this blower is controlled by the setting of the heat level output indicator.

When operating on LOW HEAT LEVEL, the feed rate can be adjusted, using the auger trim, for different quality fuels. These settings can be used if the fire keeps going out on low (for poor quality fuel) or if the

low setting is too hot for the room (see “OPERATING INSTRUCTIONS - CONTROL BOARD FUNCTIONS”).

THERMOSTAT / SWITCH MODE:

INITIAL START-UP: See above

OPERATION - HI / LOW mode: When the thermostat contacts are closed the stove settings are adjustable as per Manual Mode (see above). When the thermostat contacts open, the circuit board will take control of the settings. The stove will drop down to a low burn until the thermostat contacts close again. This low burn setting can be adjusted for different fuel qualities (see “OPERATING INSTRUCTIONS

-CONTROL BOARD FUNCTIONS”). The stove will come back to the previous HEAT LEVEL setting when the thermostat contacts close again.

OPERATION – ON / OFF mode: When the thermostat contacts close, the unit will light automatically. Once up to temperature, the stove operates the same as in manual mode (see above). When the thermostat contacts open, the unit automatically begins its shutdown routine. The stove will re-light when the thermostat contacts close again.

TURNING YOUR PELLET STOVE OFF:

•MANUAL and HI / LOW mode: To turn the unit OFF, simply press the ON / OFF button. This will stop the feed of pellets. The blowers will continue to operate and cool the stove down. When cool enough, the stove will turn off.

•ON / OFF mode: To turn the unit OFF, turn the thermostat down or off.

DO NOT unplug unit while Combustion fan is operating.

This may lead to smoke escaping from the stove.

8

Page 7 Page 9
Page 8
Image 8
Enviro C-10804, Empress owner manual Thermostat / Switch Mode, Initial START-UP See above
Page 7 Page 9

C-10804, Empress specifications

Enviro Empress, model C-10804, is a cutting-edge integrated environmental management system designed to address the pressing needs of modern sustainability practices. This innovative solution combines advanced technologies to promote eco-friendly operations across various sectors, including agriculture, manufacturing, and urban planning.

One of the main features of the Enviro Empress C-10804 is its comprehensive data analytics capability. By utilizing machine learning algorithms and big data, it collects and analyzes real-time environmental data, allowing users to make informed decisions about resource allocation and waste management. This feature not only minimizes environmental impact but also enhances operational efficiency.

The C-10804 incorporates smart sensor technology, which monitors air and water quality, soil health, and energy consumption. These sensors provide continuous data streams, enabling users to identify potential issues before they escalate. For instance, if air quality drops below acceptable levels, the system can automatically activate air purification measures, ensuring compliance with environmental standards.

Another characteristic of the Enviro Empress is its modular design, allowing for easy scalability and integration into existing systems. This flexibility makes it suitable for small businesses and large enterprises alike. Companies can start with essential features and gradually expand their system as their environmental management needs evolve.

In addition, the C-10804 includes an intuitive user interface, which facilitates easy navigation and data interpretation. Users can visualize their data through customizable dashboards, enabling them to track progress toward sustainability goals efficiently. This feature empowers stakeholders at all levels to engage with environmental initiatives and fosters a culture of accountability within organizations.

Moreover, the Enviro Empress C-10804 supports renewable energy integration, making it easier for users to transition to sustainable power sources. By monitoring energy consumption patterns, the system can identify opportunities for solar or wind energy utilization, contributing to overall carbon footprint reduction.

Overall, Enviro Empress C-10804 is a powerful tool for organizations looking to enhance their environmental performance. With its advanced technologies, data-driven insights, and user-friendly features, it stands as a pivotal solution in the pursuit of sustainability and responsible resource management. As businesses increasingly prioritize environmental stewardship, the Enviro Empress will play a crucial role in shaping a greener future.
Top Page Image Contents