Initial Installation

REPLACING THE BLOWER:

 

1.

Turn the unit off and remove the log set.

2.

Remove the brick liner.

3.

Remove the burner tray assembly by removing the

 

screw on either side of the tray, between the front and

 

rear burners. Lift the tray out.

4.

Remove the four (4) 5/16” bolts that hold the blower

 

mounting plate to the back firewall. Use a light

 

lubricating oil on screws before removal.

5.

Carefully pull the blower assembly into the firebox

 

(see Figure 8) disconnect the blower leads from the

 

harness and remove blower.

6. To re-install, check mounting plate gasket if damaged

 

replace with new one and reverse steps 1 through 4.

 

Refer to “Secondary Installation - Installation of Panel

 

Set” and “Secondary Installation - Installation of Log

 

Set and Embers”.

Figure 8: Blower (Fan) Removal.

 

ADJUSTING THE VENTURIES:

•There is a separate venturies for each burner, see Figure 9.

•Remove one screw from the cover plate located below the ash shelf and loosen the other screw (do not remove) swing the cover plate out of the way and tighten screw down to hold it in place.

•With along screwdriver rotate spring clips to open or close the venturies to the desired setting.

The venturies allows the amount of air coming into the fireplace to be adjusted in order to accommodate different climates and venting arrangements. Start the pilot and then the burner. Make sure the pilot flame is burning normally and none of the burner ports are plugged. Let the fireplace burn for roughly fifteen9minutes and then examine the flames, compare the flames to Figure 16.

Rear log holder

 

Front log holder

Ember tray &

Rear burner

front burner

 

Door

Venturies

Screwdrive

 

 

Gold bar

Air shutter cover plate

Figure 9: Venturi Adjustment.

The ideal flame will be blue at the base and light orange above. The flames should be of medium height. If the flames look like this, no venturi adjustment is needed. If the flames are fairly short and mostly blue, the fireplace is getting too much air. Therefore, the venturies should be closed slightly until the correct flames are achieved. Flames that are very orange, with tall, dark, stringy tips, are not getting enough air. Open the venturi until the flames clean up. If the venturi is opened, or closed all the way, and the correct flames cannot be attained, turn off the gas and contact the dealer.

Warning: Incorrect venturi adjustment may lead to improper combustion, which is a safety hazard. Contact the dealer if there is any concern about the venturi adjustment.

10

Page 9 Page 11
Page 10
Image 10
Enviro EG40-071 owner manual Turn the unit off and remove the log set
Page 9 Page 11

EG40-071 specifications

The Enviro EG40-071 represents a cutting-edge advancement in eco-friendly technology, engineered for both performance and sustainability. This device is a perfect embodiment of modern environmental solutions, making it an ideal choice for various applications ranging from industrial processes to residential use.

One of the standout features of the Enviro EG40-071 is its high efficiency. The unit utilizes advanced energy management systems that optimize power consumption while delivering impressive output. With a focus on reducing environmental impact, the EG40-071 is designed to operate with minimal energy waste, thereby lowering operational costs and promoting greener practices.

Moreover, the technology integrated into the Enviro EG40-071 is state-of-the-art. It includes sophisticated monitoring systems that provide real-time data on performance metrics. This feature allows users to track energy usage, emissions, and operational efficiency, enabling informed decision-making and streamlined performance. The device is also equipped with IoT capabilities, facilitating remote access and management through connected devices. This modern connectivity feature means users can monitor and control the unit from anywhere, enhancing convenience and overall functionality.

In terms of design, the Enviro EG40-071 boasts a robust and compact structure, making it suitable for various installation settings. Its modular design enables easy integration into existing systems, while the durable materials used in its construction ensure longevity and reliability even in challenging environments. Additionally, the device adheres to stringent safety standards, providing peace of mind for users.

One of the key characteristics of the Enviro EG40-071 is its versatility. It can be utilized in diverse applications, including HVAC systems, industrial machinery, and renewable energy projects. This adaptability makes it a valuable asset for businesses and households striving to reduce their carbon footprint. Furthermore, the EG40-071 contributes to compliance with environmental regulations, allowing users to align with sustainability goals and practices.

In conclusion, the Enviro EG40-071 combines advanced technology, efficiency, and versatility, making it a significant player in the realm of eco-friendly solutions. With features that support energy management and monitoring, alongside a robust and modular design, it stands out as a key component for those looking to embrace sustainable innovation in their operations. The Enviro EG40-071 is not just a product; it is a commitment to a greener future.
Top Page Image Contents