Problem

Possible Cause

Solution

 

Spark will not light the pilot after

Defective piezo igniter

Check connections to igniter

repeated pressing of spark igniter

 

-If igniter connections are good but

 

 

there is no spark-replace igniter

 

Broken spark electrode

-Check for broken ceramic insulation

 

 

replace, electrode if broken

 

Miss-aligned spark electrode

-If spark is not arcing from the

 

 

electrode to pilot- adjust by loosening

 

 

screws on pilot base. Adjust and re-

 

 

tighten

 

Pilot will not remain lit

Problem with thermocouple circuit

-Check for proper connection of

 

 

thermocouple to rear of valve. If

 

 

loose, tighten lightly

 

 

-Check pilot for full flame

 

 

impingement around thermocouple.

 

 

If the pilot is to small - Check gas

 

 

pressure, adjust pilot rate screw,

 

 

check pilot head for blockage.

 

 

-Check thermocouple voltage at

 

 

valve- must be greater than 5 mV. If

 

 

low , replace thermocouple.

 

Air in gas line - (Pilot flame dies while knob

-Bleed line.

 

 

is depressed.)

-Check gas line pressure.

 

 

-Contact dealer.

Burners will not remain lit

Problem with thermopile circuit

-Check gas line pressure.

 

 

-Check for flame impingement on

 

 

thermopile, if low see “Pilot will not

 

 

stay lit”

 

 

 

-check thermopile for a Minimum of

 

 

300 mV

when burner switched

 

 

on.

 

 

 

-Check wiring to thermostat for

 

 

breaks.

 

Flame lifting

Leak in vent pipe

-Check for leaks in vent connections

 

Improper vent configuration

-Check vent configuration with

 

Terminal may be recirculating flue gases

manual

 

 

 

-Check to see if terminal is on

 

 

correctly

 

 

 

-May need to install high wind

 

 

termination cap

 

 

-Contact dealer.

Glass fogs up

Normal conditions - after the appliance warms

up glass will clear

 

** Due to additives in gas, glass may get hazy during normal use**

 

Clean when needed.

 

 

Blue flames

Normal during start - flame will yellow as the

 

 

 

appliance heats up.

 

 

Flames are burning “dirty” or

Flame impingement

-Check log position

Sooting

 

-Increase primary air by opening

 

 

venturi shutters

 

 

See also “Burners will not stay lit”

11

Page 10 Page 12
Page 11
Image 11
Enviro EG 28 B owner manual Problem Possible Cause Solution
Page 10 Page 12

EG 28 B specifications

The Enviro EG 28 B is an innovative solution in the realm of environmental technology, specifically designed for efficient waste management and energy resource recovery. This advanced equipment stands out in both functionality and sustainability, making it suitable for various applications in municipal and industrial settings.

One of the main features of the Enviro EG 28 B is its robust waste processing capability. The system can handle a diverse range of materials, including organic waste, plastics, and other recyclables. This flexibility allows users to maximize the efficiency of their waste management operations, promoting a circular economy. The unit is designed with a high throughput capacity, enabling it to process large volumes of waste without sacrificing performance.

The Enviro EG 28 B utilizes cutting-edge technologies to optimize every phase of waste treatment. Integrated sensors and automated controls monitor the waste processing in real-time, ensuring that the system operates at peak efficiency. This not only maximizes the recovery of valuable resources but also minimizes energy consumption. The inclusion of advanced sorting mechanisms further enhances the unit's effectiveness, allowing for the precise separation of materials for recycling and composting.

Another characteristic that sets the Enviro EG 28 B apart is its environmentally friendly approach. The equipment is engineered to significantly reduce greenhouse gas emissions throughout its operational lifespan. It employs a closed-loop system that captures and repurposes gases generated during processing, turning potential pollutants into usable energy. This aligns with global sustainability goals and positions the Enviro EG 28 B as a leader in eco-conscious waste management solutions.

Additionally, the Enviro EG 28 B is designed with user-friendliness in mind. The intuitive interface allows for easy operation and maintenance, ensuring that operators can manage the system without extensive training. Moreover, its compact design is adaptable to various locations, allowing for installation in space-constrained environments while maintaining high operational standards.

Overall, the Enviro EG 28 B exemplifies the future of waste management technology, combining efficiency, sustainability, and ease of use. Its innovative features and technologies not only help reduce environmental impact but also provide significant economic benefits to organizations seeking to optimize their resource management practices. As the need for effective waste processing continues to grow, the Enviro EG 28 B stands ready to meet these challenges head-on.
Top Page Image Contents