Epson 4113114-06 Notice for CD/DVD Discs

❏Be careful when you handle used ink cartridges, as there may be some ink remaining around the ink supply port. If ink gets on your skin, wash the area thoroughly with soap and water. If ink gets into your eyes, flush them immediately with water. If discomfort or vision problems remain after a thorough flushing, see a doctor immediately.

❏Do not remove or tear the label on the cartridge; this can cause leakage.

❏Install the ink cartridge immediately after you remove it from its package. If you leave a cartridge unpacked for a long time before using it, normal printing may not be possible.

❏Use the ink cartridge before the expiration date printed on its package.

❏Do not dismantle ink cartridges or try to refill them. This could damage the print head.

❏After bringing an ink cartridge inside from a cold storage site, allow it to warm up at room temperature for at least three hours before using it.

❏Store ink cartridges in a cool, dark place.

❏Do not touch the green IC chip on the side of the cartridge. Doing so may prevent normal operation and printing.

❏The IC chip on this ink cartridge retains a variety of cartridge-related information, such as the ink cartridge status, so that the cartridge may be removed and reinserted freely. However, each time the cartridge is inserted, some ink is consumed because the product automatically performs a reliability check.

❏Do not place ink cartridges with the ink supply area facing down. This may result in ink leakage. Also, dirt attached to the ink supply area may result in the product not functioning properly.

Notice for CD/DVD Discs

Before using the product, an operation check should be conducted to ensure the unit’s functionality. Also, back up the data on the CD/DVD, if needed. Data may be damaged or lost in the following cases:

-Influence of static or electrical noise -Incorrect usage

-Malfunction or repair

-Damage due to natural disaster

Epson does not hold any responsibility for lost or damaged data, due to causes not limited to those listed above, even the product is under warranty period.

Important Notice and Safety Instructions 10

Contents

Page Copyright and Trademarks Contents Copyright and Trademarks Important Notice and Safety Instructions Chapter 1 Using Your Software Chapter 2 Publishing Discs Chapter 3 Replacing Ink Cartridges Chapter 4 Maintaining Your Product Chapter 5 Troubleshooting Appendix A Where To Get Help Appendix B Product Information Important Notice and Safety Instructions Important Note Important Safety Instructions Choosing a Place for the Product Using the Product Handling Ink Cartridges Notice for CD/DVD Discs Concerning Incidental Loss Arising out of Use of this Product About Usage Limitation Warnings, Cautions, and Notes WARNING FCC Compliance Statement For American Users For Canadian Users DECLARATION of CONFORMITY Chapter Using Your Software System Requirements Windows requirements Page Setting a Working Folder and Log Adding the Product Setting for Notification of Job Completion Overview of Applications Using EPSON Total Disc Maker Overview of Printer Driver From EPSON Total Disc Maker From EPSON Total Disc Setup From Windows applications From the Start menu Uninstalling Software Publishing Discs Introduction Standard Mode External Output Mode Batch Mode Drive to be used Number of write retries Printer name Failure error mark Page Precautions for Duplicating CDs/DVDs Printing on CDs/DVDs with a Commercially Available Software Package Notice for Barcode Printing Standard Mode 4. Load CDs/DVDs into stacker 1 with the printable side facing up 5.Insert stacker Accessing EPSON Total Disc Maker Registering Data Disc Apply Page Creating Labels Label Template Background Edit Item Layout Making the Stacker Settings Publish 3.Set Stacker Settings ❏Publish Mode: Select Standard Mode ❏Stacker 2: Output Stacker will be displayed Page Page External Output Mode Page 6. Take out stacker 8.Load CDs/DVDs into stacker 2 with the printable side facing up 9. Insert stacker 10.If you select stacker 3 as the output stacker, insert stacker Page Page Page Page Page Page Page ❏Publish Mode: Select External Output Mode Output stacker Do not use Page Page Batch Mode Page Page 10.Insert stacker Page Page Page Page Page Page Page ❏Publish Mode: Select Batch Mode Page Taking Out Discs Page Pausing Publishing Resuming Publishing Canceling Publishing Priority Publishing Replacing Ink Cartridges Checking the Ink Cartridge Status Precautions on Ink Cartridge Replacement Replacing an Ink Cartridge This table describes the status of the lights and the actions you need to take To replace an ink cartridge, follow the steps below 1.Make sure that the Power light is on, but not flashing 2.Open the ink cartridge cover 3. Push in the used cartridge so the cartridge pops out slightly Remove the new ink cartridge from the package Page Maintaining Your Product Checking the Print Head Nozzles Cleaning the Print Head Using the Head Cleaning Utility <Normal><Clogged Follow the steps below to clean the print head using the head cleaning utility 1.Make sure the product is turned on 2.Make sure no lights indicate errors and the disc cover is closed Aligning the Print Head Correcting the Printing Position Cleaning Your Product 2.Open the disc cover, and remove the stackers from the product 4.Place the stackers back in position Cleaning the Filter Clean the filter located on the rear of the product once every six months 2.Loosen and remove the screws from the filter covers to open them 3. Remove the filters from the filter covers Getting Maintenance Information Transporting Your Product Page Troubleshooting Diagnosing the Problem Error associated with cover Error associated with disc transfer Error associated with stacker Page Error associated with ink Error associated with product Error associated with drive Other error Checking Product Status When you access EPSON Total Disc Monitor, the following window appears: EPSON Total Disc Monitor provides the following information: ❏Job List: ❏Operation Guidance: ❏Ink Cartridge Status: Disc or the CD/DVD Tray Does Not Feed Correctly If the same error continues to occur, contact your dealer Multiple Disc Feeds ❏Make sure the disc stack fits under the red line in the stacker ❏Make sure none of the discs are damaged Remove the stack of discs and make sure the discs are not too thin ❏Remove discs from the stacker and fan them before loading them back Writing Problem Print Quality Problems Vertical Misalignment Banding Incorrect or Missing Colors Miscellaneous Printout Problems Incorrect Margins Printout Has a Slight Slant Printed Side is Smeared or Scuffed Printing is too Slow The Product Does Not Function Only the Power Light is On The Ink Light is Flashing or is On after you Replace the Cartridge Software Cannot be Installed Ink Pad Nearly Full Message is Displayed by the Software Disc Cannot be Published Disc Information Cannot be Read Appendix A Where To Get Help Contacting Customer Support Help for Users in the Europe (EMEA) Help for Australia Appendix B Product Information Product Parts and Control Panel Functions e f g h j k l r q p o n m Buttons Lights Ink and Disc Technical Specifications Page Page Page Page Job Processing Number of Products that can be Connected to One Computer Printing Write Speed Mechanical Electrical Environmental Standards and Approvals Interface Lifetime