Epson 9840 APPENDIX A -- MODEL 9840 SPECIFICATIONS

INTERFACE MODEL 9840 VER 6.0.2

APPENDIX A -- MODEL 9840 SPECIFICATIONS

Transducer Interface

Excitation 5VDC or 10 VDC software/auto selectable

Current Drive 180 mA at 5VDC or 10 VDC

Push Button Shunt Yes

Internal Shunt Resistor 1 standard, 2 optional. Rear panel selectable

Calibration Method Shunt, mV/V, Known Load

Push Button Tare 100% of range--display and analog output

Sensitivity Adjust 1mV/V to 4.5 mV/V

Accuracy 0.01% of full scale +/- 1 digital count

CMRR 115 dB

Additional Transducer Channel

Auxiliary Channel optional

D/A Analog Output

Full Scale Output +/- 10 VDC nominal +/- 0.5 VDC

Linearity 0.02 % of full scale

Scaling Gain and offset selected by software.

Frequency Response Approx. 15 Hz (plus filtering)

Output Source Any displayed quantity

Output Channels 1 std, 2 optional

Direct Analog Output

Full Scale Output -/+ 8.14 VDC +/- 0.25 VDC

Linearity 0.02 % of full scale

Scaling Fixed with no tare, transducer channel only

Frequency Response Approx. 1.5 kHz

Peak/Hold

Peak/Valley/Hold Digital 1/60 second capture

MODEL 9840 PG 52 PUB. 2856-16

Contents

Main CONTENTS Page Page INTRODUCTION Page QUICK START Page Page RUN MODE Item Button Tare Button Reset Button View Button Esc Button Print Button Unit Button SETUP MODE SUMMARY SETUP MODE Entering Numerical Data Entering Alphanumeric Data >User Data Entry >>Base Area Ch A/B >>Base Length Page >Sensor Select Sensor Delete >Calibration >>Cal Check >>Cal by mV/volt (2-Point or 6-Point) >>Cal by Masses or Torque (2-Point or 5-Point) >>Cal by Shunt Val >>Counts per Inch >Limits >System Options >>Printer Baud >>Auto Identify >>Auto Zero Ch A/B >>Com Address >>Com Baudrate >>Com Line Feed >>Retain Tare >>RS232 EOT Char >>Decimals Ch A/B >>Count By Ch A/B >>Second Line >>Filter Window REMOTE OPERATION Digital Inputs USB Driver Communications Settings Communications Format RS232 RUN MODE COMMAND SUMMARY RS232 RUN MODE COMMANDS Hello Command (H) Question Mark Command (?) Front Panel Display Command (F) Front Panel View Command (FV) Front Panel Set Command (FS) Front Panel Alternate Command (FA) Front Panel Pointer Control to Line 1 (F1) Front Panel Pointer Control to Line 2 (F2) Value Command (V) for one or both channels Print Command (P) Reset Tare, Peak, Valley or Position Command (R) Freeze Display Command (X) Text Display Command (T) RS232 SETUP MODE COMMAND SUMMARY RS232 SETUP MODE COMMANDS User Data Entry Command (U) User Data View Command (UV) User Data Area Command (UA) User Data Length Command (UL) Analog Output Command (A) Analog Output View Command (AV) Analog Output Set Command (AS) Sensor Command (S) Sensor View Channel A or B Command (SA or SB) Sensor View Command (SV) Sensor Select Command (SS) Sensor Delete Command (SD) Calibration Command (C) Calibration Check Command (CC) Calibration Begin Command (CB) Page Calibration Escape Command (CE) Calibrate by Millivolt-Per-Volt Command for One Point (CV) Calibrate by Millivolt-Per-Volt Command for Six Points (CMV6) Calibrate by mV/V Mass and Volt Commands (CMVM and CMVV) Calibrate by mV/V Torque and Volt Commands (CMVT and CMVV) Calibrate by Masses Command (CM) Calibrate by Masses Point Command (CMP) Calibrate by Torque Command (CT) Calibrate by Torque Point Command (CTP) Calibrate by Shunt Command (CS) Calibrate Counts-Per-Inch Command (CI) Limits Command (L) Limit View Command (LiV) Limit Set Command (LiS) Limit Setup Escape (LE) Limit Reset Command (LiR) System Options Command (O) Option View Command (OV) Option Printer Baudrate Command (OP) Option Auto-Identify Command (OI) Option Auto-Zeroing Command (OZ) Option Com Address Command (OA) Option Com Baudrate Command (OB) Option Linefeed Command (OL) Option Tare Retain Command (OT) Option End of Transmission Character (OE) Display Options Command (D) Display View Command (DV) Display Filter Command (DF) Display Decimal Command (DD) Display Count By Command (DC) Display Second Line Command (D2) Display Second Line Text (DT) Display Filter Window Commands (DW) Page SYSTEM CALIBRATION MODE APPENDIX A -- MODEL 9840 SPECIFICATIONS Page Page APPENDIX B -- CABLES AND CONNECTORS Load Cell Connectors Serial Port Connector Digital I/O Connector Chart Rec. Connector Page Precision Shunt Calibration Resistors