EPL-6000 LASER PRINTER

Mechanical

Dimensions and

 

 

weight:

Height:

8.3 inches (210 mm)

 

Width:

16.1 inches (410 mm)

 

 

excluding output and

 

 

input trays.

 

Depth:

15.4 inches (390 mm)

 

Weight:

Approx. 36 lb. (16 kg)

 

 

including paper cassette,

 

 

drum unit, and toner

 

 

cartridge.

Recommended

 

 

duty cycle:

3,000 sheets per month

MPBF (Mean Prints

 

 

Between Failures):

30,000 sheets

MTBF (Mean Time

 

 

Between Failures):

3,000 hours

 

Durability:

5 years or 300,000 sheets

 

(whichever comes first)

Electrical

Voltage:120 VAC ± 10%, 60Hz ± 3Hz

Power consumption: 600W

Controller hardware

RAM:Total Memory: 512K bytes

2MB Memory

Board:The optional 2MB memory board provides enough memory for full-page (letter size), 300 dpi graphics plus additional memory for downloading and other purposes.

1 Interface Specifications 1

Pin assignments for the parallel interface

The parallel interface connector pin assignments and a description of the interface signals are shown in the table below.

Signal

Return

 

 

 

 

Pin

Pin

 

Signal

Direction

Description

 

 

19

 

DATA

 

Signal to read data I”

 

 

 

 

 

 

 

 

 

20

 

DATA 1

 

These signals represent

 

 

21

 

DATA 2

 

information of me 1st to

 

 

22

 

DATA 3

 

8th bits of parallel data

 

 

23

 

DATA 4

 

respectively. Each signal

 

 

24

 

DATA 5

 

is at HIGH level when data

 

 

25

 

DATA 6

 

is logical 1 and LOW when

 

 

26

 

DATA 7

 

 

 

 

27

I

DATA 6

I

 

 

 

 

 

 

10

 

I26

lm

1 O U T

1 Acknowledge receiving data.

 

 

 

 

 

 

 

I-

 

 

im

IN

Initial stage after data inside

 

 

 

 

buffer is printed.

 

 

 

 

 

32

-

FAULT

OUT

This signal becomes LOW

4MB Memory B a r d :

Environment

Operation:

4MB increases capacity for downloading of fonts, graphics, etc.

Temperature: 50 to 95°F (10 to 35°C)

Humidity: 20 to 80% RH without condensation

 

 

 

 

when

the printer is:

 

 

 

 

.

off

line

 

 

 

 

•

in error state

 

 

 

 

•

malfunctioning.

 

 

 

 

 

33

34

NC

 

Not defined.

 

 

 

 

 

 

 

t 35

36

NC

-

Not

defined.

 

Storage:

Temperature: 32 to 95°F (0 to 35°C)

 

Humidity:

20 to 80% RH without

 

 

condensation

WARNING: The life of consumables may be significantly reduced if they are stored at temperatures outside the range stated above.

Internal mode

HP LaserJet series II emulation

•AU interface conditions are based on TTL. level. Both the rise and fall of each signal must be less than 0.2 microseconds.

•The column heading ‘Direction” refers to the direction of signal flow as viewed from the printer.

. “Return” denotes the twisted-pair return, to be connected at signal ground level. For the interface wiring, be sure to use a twisted-pair cable for each signal and to complete the connection on the return side. These cables should be shielded and connected to the chassis of the host computer and the printer.

EPL-2

7 / 1 8 / 8 9

Laser Printers