Manuals / Esoteric / Home Audio / Stereo Amplifier

Esoteric AI-10 Basic Operation, To turn the unit off standby, Turn the connected components off

Models: AI-10

1 22

Download 22 pages 28.02 Kb

Page 12

Basic Operation

Basic Operation

3

2

4

1First of all, turn on the power of the connected components.

2Press the POWER button to turn the AI-10 on.

power indicator

If the power indicator is red, press the ON button of the remote control unit to turn the unit on (see page 11).

It may take several seconds for the unit to start outputting sounds. Wait until “WAIT ...” disappears from the display.

3Select an input by turning the INPUT knob.

The current input appears on the left of the display. Repeatedly turn the knob until the desired input appears on the display.

COAX, OPT, LINE1, LINE2, LINE3,

LINE4 or PHONO*, i.LINK**

*: PHONO appears only when the LINE/PHONO switch is set to

PHONO.

<“COAX” or “OPT” blinks when the unit cannot perceive the digital signal. In that case, connect a digital device to the DIGITAL IN (COAXIAL or OPTICAL) terminal and switch it on.

**: “i.LINK” will be added after a future hardware upgrade (charged). i.LINK indicator blinks when the unit cannot perceive the digital signal. In that case, connect a digital device to the i.LINK(AUDIO) terminal and switch it on.

4Play the source, and gradually turn up the volume to the required level by turning the VOLUME knob.

To turn the unit off (standby)

To prevent sudden noise from the speakers, make sure to turn the unit off in the following way.

1.Stop the playback of the connected component.

2.Turn the AI-10 off using the POWER button.

<Use the STANDBY button of the remote control unit to turn the AI-10 standby.

3. Turn the connected components off.

12

Image 12

Esoteric AI-10 Basic Operation, To turn the unit off standby, First of all, turn on the power of the connected components

Contents

Digital Integrated Amplifier MANUEL DU PROPRIÉTAIREOWNER’S MANUAL IMPORTANT SAFETY INSTRUCTIONS Contents CAUTION Regarding PlacementFor U.S.A For European customers Disposal of your old applianceMaintenance Before UseSpeaker Connection What’s in the boxConnection using speaker cables with spades or bare wire Connection using speaker cables with banana plugsWhen your speaker cable has bare wire at the end ENGLISHConnection CD player, DVD player, etcSuper Audio CD player SA-10 etc CD player, DVD player, tuner, etcC SIGNAL GND connection E Power cord receptacleLINE/PHONO switch A Analog audio input terminals LINE INFollowing settings are necessary for this connection AI-10 SZ-1/UZ-1/SA-10 upgradedF Reserved slot for i.LINK AUDIO terminals UZ-1Remote Control Unit Restoring factory settingsHow to insert the batteries Battery ReplacementRemote Control Unit Identifying the PartsA B C D G F ERemote Control Unit B Power indicator Blue onC POWER D SETUP1 First of all, turn on the power of the connected components 2 Press the POWER button to turn the AI-10 on2. Turn the AI-10 off using the POWER button Basic OperationUse the DIMMER button to cycle between these settings FL Dimmer3 2 Use the WORD button to switch between WOUT and WORD OFF WOUT onMuting Display DimmingGain Setting for Analog Audio Input 2 Press and hold the SETUP button for more than 2 seconds3 Turn the INPUT knob to change the Gain setting Name and Skip Setting of the INPUT Knob 1 Press and hold the SETUP button for more than 2 seconds3 Turn the INPUT knob to change the setting ExampleSettings for Word Sync, Volume and i.LINK SVOL starting volumeOFF default WOUT Word sync output frequencyiRC i.LINK remote control function OFF factory settingSZ-1, UZ-1 SA-10 upgraded CH ChannelHow to connect multiple i.LINK-capable devices i.LINK IEEECopyright protection system DTCP Data transfer rateTroubleshooting No powerRemote control doesn’t work Other units with remote controls operate incorrectlySpecifications AccessoriesGeneral Digital Input TerminalsSommaire Avant utilisationContenu de l’emballage Lisez ceci avant utilisationTEAC ESOTERIC COMPANY Model numberSerial number 0307 . MA-1193A