Before Unpack your cooler and install the casters. Slip the Operation stems of the casters into the holes provided in the bot-

tom of the front and back grille.

EVAPORATIVE COOLER

OPERATION

CAUTION: To reduce the risk of fire or electrical shock, do not use this fan with any solid state speed control device.

Select the area you wish to cool. Evaporative coolers work best near a partially opened door or window to draw in fresh air. An equal amount of air should be discharged out of the room to dispel heat and humidity.

Fill Reservoir Fill the reservoir from the back. The reservoir holds 5 1/2 gallons of water. DO NOT OVER FILL. Water will leak out and could cause water damage to the sur- rounding area. If the reservoir runs dry, it will not harm the pump. When transporting the unit to a different location, be very careful not to spill the water. It is best to re-locate the cooler, and then add water.

Float Included is a float for continuous fill. To attach the Installation float, remove the back grille. Remove the nuts from

the float and insert the float into the water shield and then through the hole in the housing. Secure the float with the nut that was removed. You may connect ei- ther a 1/4 inch hose or a garden hose using the garden hose adapter. Adjust the float so that the water level is about an inch below the top of the reservoir. Reinstall the back grille.

Operation Plug the electrical cord into a 115-120 volt grounded outlet. You may operate your cooler on one of three speeds: low, medium or high. Turn the switch knob clockwise to activate the pump and fan. This will cool the air. Turn the switch counterclockwise to operate the cooler as a fan only (pump will be off).

MAINTENANCE

CAUTION: To reduce the risk of fire, always unplug the cooler before attempting service of any kind.

Motor No oil or lubrication is necessary. The motor is perma- nently lubricated at the factory.

Pump No oil or lubrication is necessary. Clean any debris from under the pump in the inlet area.

Filter Remove the filter from the rear grille and rinse with water. Be careful not to damage the filter! The filter should be replaced every two years or if it becomes clogged.

Water Tank Drain and clean the water tank. To drain, remove the back grille and disconnect the clear hose from the black tube. Turn unit on cool and pump out most of the water. Wipe dry and clean with a towel. Before reattaching the back grille, reconnect the clear hose to the black water tube.

TROUBLE SHOOTING

CAUTION: Always unplug the cooler before attempt- ing service of any kind.

PROBLEM: POSSIBLE CAUSE/REMEDY:

Cooler Does

Not Pump 1. The pump hose may have worked loose. Check the Water connection at the pump and at the water tube located

in the back grille assembly. Reconnect pump hose if necessary.

2.The water tube may be blocked. Remove the tube and clean it out. Make sure water holes are clear.

3.The pump or switch may be defective. Replace pump or switch, if necessary.

PROBLEM: POSSIBLE CAUSE/REMEDY:

Fan Does Not

Operate 1. Verify there is 115-volt power at the electrical outlet. Check the fuse or breaker.

1.The fan switch or motor may be defective. Replace if necessary.

LIMITED WARRANTY

This warranty is extended to the original purchaser only. It does not cover damages incurred during shipping or through accident, neglect, or abuse by the owner. Essick Air Products/Champion Cooler does not authorize any person or representative to assume any other or different liability in connection with this cooler.

Terms And All original parts provided by Essick Air Products/ Conditions Champion Cooler are warranted against defects in Of Warranty material or factory workmanship for one year.

Exclusions Essick Air Products/Champion Cooler is not respon- From sible for incidental or consequential damage resulting

Warranty from any malfunction.

Essick Air Products/Champion Cooler is not respon- sible for any damage occurring from the use of water softeners, chemicals, de-scale material, or if a higher horsepower motor is used in the unit other than what Essick Air Products recommends.

Essick Air Products/Champion Cooler is not respon- sible for the cost of service calls to diagnose cause of trouble, or labor charge to repair and/or replace parts.

How To Contact the Dealer where you purchased the evapora- Obtain tive cooler. If for any reason you are not satisfied with Service the response from the Dealer, contact the Customer

Under This Service Department: Essick Air Products, 5800 Warranty Murray Street, Little Rock, Arkansas 72209 or call 800-

643-8341.

Register Register your product online at:

Product www.essickair.com/eac/onlineregistration-eac.htm

Page 1 Page 3
Page 2
Image 2
Essick Air M150 instruction manual Evaporative Cooler Operation, Maintenance, Trouble Shooting, Limited Warranty
Page 1 Page 3

M150 specifications

The Essick Air M150 is a robust evaporative cooler designed to deliver energy-efficient cooling solutions for homes and small commercial spaces. With its sleek design and powerful functionality, the M150 stands out in the market as a reliable option for maintaining comfortable indoor temperatures during the sweltering summer months.

One of the main features of the Essick Air M150 is its high air flow capacity. It is capable of producing up to 3,500 CFM (cubic feet per minute) of airflow, making it ideal for spaces up to 1,500 square feet. This impressive airflow is achieved through the use of a powerful motor and large fan blades that help circulate cool air effectively throughout the area.

The M150 utilizes evaporative cooling technology, which draws in hot air, passes it over water-saturated pads, and cools it through the process of evaporation. This method not only provides efficient cooling but also adds moisture to the air, making it ideal for dry climates. Unlike traditional air conditioning systems, the M150 consumes significantly less energy, allowing for lower electricity bills while contributing to a more sustainable environment.

Another notable characteristic of the Essick Air M150 is its user-friendly design. It includes adjustable air louvers to direct airflow where it's needed most and has an easy-to-navigate control panel, making it simple to customize the cooling experience. The unit also features a large water reservoir that can hold approximately 10 gallons, allowing for extended periods of operation without the need for frequent refills.

The M150 is built with durability in mind, featuring a sturdy yet lightweight construction that allows for easy mobility. It comes equipped with casters, enabling users to effortlessly move it from room to room or even outdoors for patio or backyard cooling.

In terms of maintenance, the Essick Air M150 is designed to be low-maintenance. The cooling pads are easily accessible for replacement, ensuring optimal performance over time.

In summary, the Essick Air M150 is an energy-efficient evaporative cooler offering powerful cooling performance, ease of use, and low maintenance. With its combination of effective moisture addition and efficient airflow, the M150 provides a comfortable indoor environment ideal for summer heat, setting it apart as a valuable addition to any home or modest commercial space.
Top Page Image Contents