Euro-Pro EP603H Changing & Cleaning the Pre- Motor Filter, Extending The Telescopic Tube

Fig. A

Wash once a month or when suction appears reduced

Warning: Allow 24 hours for drying before replacing in unit.

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

PLEASE NOTE: The white pleated filter material in the HEPA Filter will discolor over time -This is NORMAL and will NOT affect the performance of the filter. If the HEPA Filter

is properly "TapCleaned” after each use and suction does not return to 100%, then we suggest that the HEPA filter be “TapCleaned”

Changing & Cleaning the Pre- Motor Filter

The pre-motor filter is a washable filter but should be replaced every three (3) months.

• Remove the dust cup container, the

Non-Woven Pre- Filter and the HEPA

filter to remove the pre-motor filter.

(Fig 13)

• Rinse the pre-motor filter in lukewarm

water and air dry the filter completely

for 24 hours. Do not use a washing

machine to rinse the filter.

Do not use a hair dryer to dry it. Air

WARNING: Always remove the power plug from the wall outlet before assembling or removing accessories.

EXTENDING THE TELESCOPIC TUBE

Push the locking button and pull the larger tube up. (Fig. 1)

ATTACHING THE FLOOR BRUSH TO THE MAIN UNIT

•Insert the floor brush into its location, in the direction of the arrow. (Fig. 3)

•To remove the floor brush from the main unit, press on the floor brush release button and pull the floor brush out.

vigorously until no more dust can be removed,

then rinsed under the faucet and allowed to dry for 24 hours before refitting into the vacuum. (Fig. A) This should be done once a month or when suction appears to be reduced.

CAUTION: The suction hole must be open, free of any obstructions at all times. Otherwise, the motor will overheat and could become damaged.

Warning: Always empty the dust cup container and clean the HEPA filter, Non-Woven Pre-Filter and Debris Screen before each use and during prolonged usage.

Never over fill the dust cup container - remove dirt and clean the HEPA filter, non-woven pre-filter and debris screen when dirt in dust cup is at or below the "MAX" level during prolonged usage or risk motor damage.

dry only. Never operate the vacuum

without the pre-motor filter in place.

• When the filter is dry, replace into the

unit and replace the HEPA filter and

dust cup container.

• A severely soiled or clogged filter

should be thoroughly washed with

fresh tepid water. A mild detergent

can be used if required.

Pre-Motor

Filter

Fig. 13

Changing & Cleaning the Post Motor Filter

The post motor filter is a washable filter but should be replaced every three (3) months.

•	Remove the filter cover from the front
	of the unit and remove the filter.
	(Fig. 14)
•	Rinse the post motor filter in lukewarm

Locking	Fig. 1
Button

INSERTING THE TELESCOPIC TUBE INTO THE MAIN UNIT

•Insert the telescopic tube into the hole next to the dust cup handle. Make sure that the slot in the handle fits correctly into the opening. (Fig. 2)

•To remove the telescopic tube, press the telescopic tube release button and pull the tube up.

Floor Brush

Release

Button

Fig. 3

ATTACHING THE HOSE TO THE MAIN UNIT

•Hold the end of the hose.

•Insert the hose into the hose connector. (Fig.4)

If you wash the Hepa filter or the non- woven pre-filter, make sure that they have completely air dried before inserting back in the vacuum.

Please Note: The HEPA Filter is washable. It should, however, be replaced every three (3) to six (6) months to ensure peak performance of your vacuum.

The non-woven pre-filter, pre-motor and post motor filters are washable. They should however be replaced every three

(3)months to ensure peak performance of your vacuum.

Important: Make sure that ALL filters have completely air dried before re- installing back in the vacuum.

water and air dry the filter completely

for 24 hours. Do not use a washing

machine to rinse the filter. Do not

use a hair dryer to dry it. Air dry only.

Never operate the vacuum without the

post motor filter in place.

• When the filter is

dry, replace into the

filter cover and

replace the filter

cover to the unit.	Fig. 14
• A severely
soiled or clogged

filter should be thoroughly washed

with fresh tepid water. A mild

7detergent can be used if required.

Fig. 2

Fig. 4

4