Euro-Pro SV70 manual Battery Pack Replacement & Disposal, Wall Mounting Bracket Optional, Problem

Fig. 8

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

Battery Pack Replacement & Disposal

Your Cordless Vacuum is powered by Nickel-Cadmium Ni-Cd) batteries, which must be recycled or disposed of properly in accordance with state, federal and local laws.

If uncertain as to how to remove the battery pack, we suggest you take your hand vacuum to a reputable small appliance service technician to have this service preformed.

Do NOT attempt to replace the batteries used in this product with any other type of battery.

The battery pack of your cordless vac is replaceable, however care should be taken when doing so. Follow these steps when replacement is required:

1.Using a #1 Phillips head screw driver, remove the single screw securing the battery compartment cover located on the under side of the unit.

2.To remove the cover, press down on the battery compartment cover while sliding towards the rear of the unit.

NEVER open the battery compartment except to change the battery.

3.Set aside battery compartment cover and screw.

4.Using the same Phillips screw driver, remove the single screw securing the battery strap. Lift off the battery strap and set aside with screw.

5.Carefully lift out battery pack and disconnect the terminals. (Fig. 8)

6.Connect the terminals to the new battery pack taking care to connect the black lead (-) to the negative connector first and the red lead (+) to the positive connector second. Place the

new battery into the battery compartment.

7. Tuck the wiring inside the

battery compartment so that the wiring does not interfere with the battery compartment cover when it is replaced.

8.Re-install the battery strap and battery compartment cover.

5

WARNING: NEVER use ordinary batteries for replacement, as these may leak and damage your vacuum cleaner. Use only battery pack XB14726 provided by EURO-PRO Operating LLC for replacement.

CAUTION: NEVER use the unit without the battery compartment cover in place.

Note: Any other servicing should be performed by an authorized service representative.

CAUTION

•Use only with the battery pack supplied with the unit.

•Do not attempt to remove the battery pack from the unit to charge it.

•Never attempt to throw the battery pack or unit into a fire or incinerate it.

•Do not attempt to remove or damage the battery casing.

•Battery must be recycled or disposed of properly at the end of it's service life.

•Do not place batteries on metal surfaces.

•Do not touch metal parts of the batteries together as the batteries will overheat.

Wall Mounting Bracket (Optional)

1.Make sure that the intended wall area for the wall mounting bracket to be drilled is free from any hidden electrical wires, water pipes and gas lines.

2.Select an appropriate place close to a wall power outlet (120V., 60 Hz).

3.Do not mount near direct sunlight, near a heat source or outdoors.

4.Select an appropriate drill type for the material to be drilled.

5.Carefully measure and mark the location of all bracket holes and then drill holes and screw the wall mounting bracket onto the wall.

TROUBLESHOOTING GUIDE

PROBLEM	POSSIBLE REASON			POSSIBLE SOLUTION
	1. Batteries discharged.		1.	Charge unit.
HAND VACUUM	2. Dead battery (battery		2.	Replace batteries. (See
		won't hold charge).		page 5.)
WILL NOT
	3.	No power in electrical	3.	Check fuse or breaker.
OPERATE
		outlet supplying		Replace fuse/reset
		transformer.		breaker.
			1.	Firmly insert the
	1. The 2 metal pins of the			motorized brush into the
MOTORIZED		motorized brush are		air-intake nozzle. This will
		not in contact with the		connect the motorized
BRUSH WILL NOT
		vacuum cleaner.		nozzle to the unit power
WORK
	2.	Motorized brush is		supply.
		clogged up.	2.	Remove all lint, hair etc.
				from motorized brush.
	1. Dust cup container is		1.	Empty dust cup container.
HAND VACUUM			2.	Remove dust cup filter
		full.
				and check for object(s) in
WILL NOT PICK-	2. Dust cup filter needs
				air duct and remove.
UP OR SUCTION		cleaning or
				Clean or replace dust cup
POWER IS WEAK		replacement.
				filter.
	3. Unit needs recharging.
			3.	Charge unit.
	1. Dust cup container is			Empty dust cup container.
DUST ESCAPING		full.	1.
	2.	Dust cup filter is not	2.	Review dust cup filter
FROM HAND
		installed correctly.		installation instructions.
VACUUM
	3.	Puncture/hole in dust	3.	Replace dust cup filter.
		cup filter.

6