OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Suitable Use of Your Pressure Washer
This high pressure washer is suitable for
The high pressure washer is suitable for washing with cold water only. The water that you use for the pressure washer must not be dirty, sandy or contain any corrosive chemical products.
The pressure washer may be used to wash shutters, doors, tiles, cars, decks, campers, etc., where high water pressure is necessary to remove dirt.
With the detergent applicator bottle, the pressure washer can be used to apply a thick coating of aerated detergent to the areas being cleaned .
When using the pressure washer we recommend the use of personal safety items to reduce the risk of accidental injury.
Unpacking Your Pressure Washer
After you open the package, check to make sure that all the parts are in the box as per parts that illustrated on page 3 of this guide. Due to transport and packing restraints, some accessories may be supplied unassembled; in this case follow the assembly instructions in this manual. If you have any questions, call Customer Service at
Correct Use of the Pressure Washer
•Place the pressure washer in a safe area and on a horizontal surface.
•When using the pressure washer, hold the trigger gun firmly with one hand on the handle and the other on the lance. (Fig. 1)
Fig. 1
•NEVER point the water jet at electric wiring, at the pump unit, or at any person or animal.
AUTOMATIC STOP SYSTEM
PLEASE NOTE: This pressure washer is equipped with the Automatic Stop System, which stops the unit during the bypass stage. To start the pressure washer, it is therefore necessary to set the On/Off switch to the “On” position; after that press the trigger: the Automatic Stop System will start the machine and will stop it automatically when the trigger is released. It is advisable to put on the safety lock of the trigger whenever the machine is stopped in order to avoid unintentional starting. Any automatic start of the machine without pressing the trigger is attributable to air bubbles in the water or other similar phenomena which do not imply the existence of any defects in the machine. Do NOT leave the appliance unattended during the standby for more than 5 minutes. Contrarily, for the safety of the appliance it is necessary to re- turn the On/Off switch to the “Off” position. Please check that the coupling of the high pressure hose with the appliance and the trigger gun supplied as standard equipment is made correctly, that is to say without any water leak.
Attaching High Pressure Hose to Pressure Washer
Note: Before attaching the high pressure hose and the garden hose coupling to the unit, remove the plastic caps from the water output and water input connections.
1.While facing the front side of the unit attach the high pressure hose to the high pressure output connector on the right side of the unit. Twist on tight to avoid leakage. (Fig. 2)
Fig. 2
3.Once the high pressure hose is connected to the unit, you can attach the lance to the end of the trigger gun. (Fig. 3)
Fig. 3
To attach the lance to the trigger gun, hold the trigger gun in your left hand insert the lance and push it in all the way into the connector on the trigger gun and turn it clockwise 60° until it locks in place. To remove the lance, push down on the attachment and turn
Garden Hose Connection
Once the high pressure hose is attached to the pressure washer, you can connect the garden hose to the unit. Before attaching the garden hose coupling to the unit, make sure that the water intake filter is inside the water intake connector on the unit.
1.Attach the male adapter (supplied) to the water intake connector on the left hand side of the unit. (Fig. 4)
2.Attach the female hose coupling to the garden hose. (Fig. 4)
3.Connect the female hose coupling to the male adapter making sure that it is tightly secured in place. (Fig. 4)
Fig. 4
4.After all the connections have been made and BEFORE you plug the pressure washer into an electrical outlet, open the water supply and press on the trigger switch in order to remove any air which may be in the hose or pump. Continue to press on the trigger switch until you get a constant flow of water coming out of the trigger gun. Allow water to flow for 30 seconds.
5.Once this is accomplished, stop pressing the trigger switch. Engage the safety lock on the trigger
6.Ensure that the "On/Off" switch, at the rear of the unit, is on the "Off" position, then plug the unit into an electrical outlet and turn the unit to the "On" position.
7.Now you are ready to use the pressure washer. Disengage the safety lock and depress the trigger on the trigger gun.
4
5
