Manuals / Exmark / Household Appliance / Vacuum Cleaner

Exmark 000 & higher manual Safety, 109-8483, 109-9361, Deck Drive Belt Routing, 109-9477, 116-0090

Models: 000 & higher

1 56

Page 12

Safety

		109-8483
1.	Throttle–fast	3.	Choke–on
2.	Throttle–slow	4.	Choke–off

109-9361

Deck Drive Belt Routing

109-9477

116-0090

116-0157

1.See Operator’s manual

116-0165

116-0205

Page 12

Image 12

Exmark 000 & higher, 4500-471, S/N 790 Safety, 109-8483, 109-9361, Deck Drive Belt Routing, 109-9477, 116-0090, 116-0165

Contents

LAZER Z MODELS For Serial Nos 790,000 & HigherPart No. 4500-471Rev. A CALIFORNIA Proposition 65 Warning Introduction Model No Serial NoContents Safety Safety Alert SymbolSafety Safe Operating PracticesDANGER SafetyDANGER Operation SafetyUsing the Rollover Protection System ROPS Slope OperationSafety Do Not mow slopes when grass is wetMaintenance and Storage SafetySafety and Instructional Decals SafetySafety 109-3148109-7232 107-2102 109-7330 107-2112Safety 109-8483109-9361 Deck Drive Belt RoutingSafety PTO Switch Symbols116-0211 Message DisplaySpecifications SpecificationsSafety Interlock System Model NumbersSeat Hydrostatic Ground Drive SystemTires & Wheels SpecificationsDimensions Cutting DeckOverall Width Overall LengthCurb Weight Accessory Weight Table WorksheetTread Width Center to Center of Tires, Widthwise SpecificationsProduct Overview Torque RequirementsProduct Overview Operation ControlsOperation Motion Control LeversIgnition Switch Hour MeterOperation PTO Engagement Switch Low Voltage IndicatorFuel Shut-OffValve Fuel GaugeOperating Instructions Pre-StartDeck Lift Pedal Transport LockOpen the Fuel Shut-OffValve Starting the EngineEngaging the PTO Disengaging the PTOStopping the Engine Driving the MachineUse caution when making turns OperationAdjusting the Cutting Height Adjusting the Anti-ScalpRollersOperation Driving in ReverseTransporting Transporting a UnitOperation Loading a Unit OperationMaintenance Recommended Maintenance SchedulesMaintenance Periodic Maintenance Check Battery ChargeService Interval Before each use or daily Service Interval As requiredCheck Safety Interlock System Check Mower BladesMaintenance Service Interval Before each use or dailyService Air Cleaner Check Rollover Protections Systems Roll Bar KnobsCheck Seat Belt Check for Loose HardwareService Interval After the first 5 hours Service Interval Every 50 hoursChange Engine Oil Check Hydraulic Oil LevelCheck Condition Of Belts Lubricate Grease FittingsLubricate Caster Wheel Hubs MaintenanceService Interval Every 200 hours Service Interval Every 100 hoursService Interval Every 500 hours Lubricate Brake Handle PivotWheel Hub - Slotted Nut Torque Specification Service Interval After the first 100 hoursCheck Spark Arrester if equipped Every 500 hours thereafterAdjustments Thread Locking AdhesivesCopper-Based Anti-seize Dielectric GreaseMaintenance 8.Raise the discharge deflectorDeck Removal MaintenanceAdjusting the Parking Brake Pump Drive Belt TensionDeck Belt Tension MaintenanceElectric Clutch Adjustment Motion Control Linkage AdjustmentMotion Control Damper Adjustment MaintenanceMotion Control Handle Adjustment Motion Control Neutral Lock Pivot AdjustmentMotion Control Full Forward Tracking Adjustment MaintenanceCaster Pivot Bearings Pre-LoadAdjustment MaintenanceRH Motion Control Shown Cleaning Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Hydro Fan Cooling GuardsBattery Disposal Waste DisposalMotor Oil Disposal MaintenanceTroubleshooting TroubleshootingTroubleshooting ProblemPossible Cause Corrective ActionSchematics SchematicsElectrical Diagram PINKSchematic ElectricalSchematics LogicHydraulic Diagram SchematicsExmark Lazer Z and Lazer Z AS Turf Equipment 3 Year Limited Commercial Warranty5 Year or 750 Hours Limited Consumer Warranty General Warranty Conditions and Products CoveredPage Page Service Record Service Done ByDate Description of Work DonePage Page MID-MOUNTRIDING ACCESSORIES AND OPTIONS OUT-FRONTRIDING ACCESSORIES AND OPTIONSWALK-BEHINDACCESSORIES AND OPTIONS