Check Mower Blades

Maintenance

2.Make sure the booster is a good and fully charged lead acid battery at 12.6 volts or greater. Use properly sized jumper cables (4 to 6 AWG) with short lengths to reduce voltage drop between systems. Make sure the cables are color coded or labeled for the correct polarity.

CAUTION

Connecting the jumper cables incorrectly (wrong polarity) can immediately damage the electrical system.

Be certain of battery terminal polarity and jumper cable polarity when hooking up batteries.

Note: The following instructions are adapted from the SAE J1494 Rev. Dec. 2001 – Battery Booster Cables – Surface Vehicle Recommended Practice (SAE – Society of Automotive Engineers).

WARNING

Batteries contain acid and produce explosive gases.

•Shield the eyes and face from the batteries at all times.

•Do Not lean over the batteries.

Note: Be sure the vent caps are tight and level. Place a damp cloth, if available, over any vent caps on both batteries. Be sure the vehicles do not touch and that both electrical systems are off and at the same rated system voltage. These instructions are for negative ground systems only.

3.Connect the positive (+) cable to the positive (+) terminal of the discharged battery that is wired to the starter or solenoid as shown in Figure 10.

Figure 10

1.Positive (+) cable on discharged battery

2.Positive (+) cable on booster battery

3.Negative (–) cable on the booster battery

4.Negative (–) cable on the engine block

5.Booster battery

6.Discharged battery

7.Engine block

4.Connect the other end of the positive cable to the positive terminal of the booster battery.

5.Connect the black negative (–) cable to the other terminal (negative) of the booster battery.

6.MAKE THE FINAL CONNECTION ON THE ENGINE BLOCK OF THE STALLED VEHICLE (NOT TO THE NEGATIVE POST) AWAY FROM THE BATTERY. STAND BACK.

7.Start the vehicle and remove the cables in the reverse order of connection (the engine block (black) connection is the first to disconnect).

Service Interval: Before each use or daily

Important: Mower blades are sharp. Wrap the blade or wear gloves, and use extra caution when servicing them.

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Lift deck and secure in raised position as stated in the Clean Grass Build-Up Under Deck section.

3.Inspect blades and sharpen or replace as required.

4.Install blade bolt and spring disc washer. Be sure the spring disc washer cone is installed towards the bolt head. Place a block of wood between front or rear baffles and the blade then torque the blade bolts to 115–120 ft-lb (156–163 N-m) (Figure 11).

977, 820 specifications

The Exmark 820,977 is a powerful and versatile commercial-grade mower that stands out in the landscaping and turf management industry. Renowned for its durability and efficiency, this model is designed to meet the demands of professionals and serious enthusiasts alike.

One of the main features of the Exmark 820,977 is its efficient engine. Powered by a robust V-Twin engine, this mower delivers impressive horsepower, enabling it to cut through thick grass and tough terrain with ease. The engine is designed for optimal fuel efficiency, reducing operational costs while maximizing performance.

The Exmark 820,977 utilizes a patented UltraCut deck technology that ensures a clean and precise cut. This innovative mowing deck design contributes to an exceptional quality of cut at various mowing heights. The fully welded construction enhances durability, allowing for prolonged use in demanding conditions.

Another significant characteristic of the Exmark 820,977 is its ergonomic design. The control system is user-friendly, providing operators with intuitive controls that minimize fatigue during extended use. The adjustable operator seat contributes to comfort, allowing for optimal positioning regardless of the user's stature.

For enhanced maneuverability, the Exmark 820,977 features a low center of gravity and responsive handling, making it easier to navigate around obstacles and tight spaces. The mower's compact design also facilitates storage and transport without taking up too much space.

Technology plays a crucial role in the Exmark 820,977's performance. The model incorporates a range of advanced features, such as an advanced ignition system, which ensures reliable starts and smooth operation. Additionally, the mower includes a maintenance display that alerts users when service is needed, promoting proactive care and reducing downtime.

The Exmark 820,977 is also designed with adaptability in mind. Optional attachments and accessories allow users to customize their mower for a variety of tasks, from mulching and bagging to aerating and dethatching. This versatility makes it an ideal choice for commercial landscapers who require equipment that can handle different jobs effectively.

In conclusion, the Exmark 820,977 epitomizes a blend of powerful performance, advanced technology, and user-friendly features. Its durability and adaptability make it a top choice for professionals seeking a reliable mower capable of delivering superior results in challenging environments.

Exmark 977, 820 manual Check Mower Blades

Models: 977 820