Extron electronic 100 setup guide Rear Panel Overview, Mount the HAE

HAE 100 • Setup Guide (Continued)

Output LEDs

zz Signal — This LED lights when the unit is providing video on the HDMI output connector. zz HDCP — This LED lights when the HDMI output signal is encrypted with HDCP.

zz Analog — This LED lights when the unit is providing analog audio from the 3.5 mm, 5-pole captive screw output connector.

zz S/PDIF — This LED lights when the unit is providing digital audio from the S/PDIF RCA output connector.

Config Port

If necessary, connect a control PC to this port using a USB cable. Use this port to update firmware and check the status of various functions.

OUTPUT

SIGNAL

HDCP

ANALOG

S/PDIF

CONFIG

Rear Panel Overview

Audio Format Switch

A toggle switch located on the rear panel is used for selecting the audio format that the HAE 100 will extract from the HDMI signal. The position of this toggle switch also governs the EDID presented to the source device connected to the input of the HAE 100.

zz Set this switch to the Analog (up) position to extract 2-channel stereo audio from the HDMI input signal.

NOTE: If the embedded audio is 2-channel LPCM, the audio can be output from the analog output and the S/PDIF output simultaneously.

zz Set this switch to the S/PDIF (down) position to extract digital S/PDIF audio from the HDMI input signal.

AUDIO

FORMAT

S/PDIF	ANALOG
L	R

Configuration DIP Switches

A 2-pole DIP switch located on the rear panel is used to configure the following features.

HDMI OUTPUT AUDIO

zz

zz

EDID Store — Set this switch to the On (up) position to enable the EDID store function (see the "EDID Store Button and LED" section below). Set this switch to the Off (down) position to disable the EDID store function.

NOTE: The EDID Store LED is unlit when this function is disabled.

HDMI Output Audio — Set this switch to the On (up) position to send audio to the

HDMI output, the Analog output, and/or the S/PDIF output simultaneously. Set this switch to the Off (down) position to send audio only to the analog output and/or S/PDIF output.

EDID
STORE	ON
ON
1	2
	OFF

EDID Store Button and LED

A recessed push-button is used to store EDID from a display that is connected to the HDMI output. With the EDID Store switch set to the On (up) position, press the recessed push-button to learn and store EDID information.

Use the LED to determine the status of the EDID storage.

zz

zz

zz

zz

Off — EDID storage is disabled. Factory default EDID is being used.

Red — EDID storage is enabled, but external EDID has not been stored. Factory default EDID is being used. Green — EDID storage is enabled and external EDID is stored.

Amber — EDID storage is enabled and EDID is being loaded. The LED turns green when stored.

Mount the HAE 100

If necessary, mount the HAE 100. For mounting information, see the HAE 100 User Guide.

Extron USA - West	Extron USA - East	Extron Europe	Extron Asia	Extron Japan		Extron China		Extron Middle East
Headquarters
+800.633.9876	+800.633.9876	+800.3987.6673	+800.7339.8766	+81.3.3511.7655	FAX	+400.883.1568		+971.4.2991800	68-2027-50
			Inside Asia Only	+81.3.3511.7656		Inside China Only		+971.4.2991880 FAX
Inside USA/Canada Only	Inside USA/Canada Only	Inside Europe Only							Rev. A
+1.714.491.1500	+1.919.863.1794	+31.33.453.4040	+65.6383.4400			+86.21.3760.1568
									02 11
+1.714.491.1517 FAX	+1.919.863.1797 FAX	+31.33.453.4050 FAX	+65.6383.4664 FAX			+86.21.3760.1566	FAX

2 © 2011 Extron Electronics All rights reserved. www.extron.com