Extron electronic DVI 201 Rx user manual Pin assignments and wiring, DVI connector pin assignments

Installation and Operation, cont’d

L	RS-232 connector — Connect a serial communications port to
	this 3.5 mm, 3-pole captive screw connector for bidirectional
	RS-232 communication. See "RS-232 connector wiring," on
	page 2-26, to wire the connector.
	N The RS-232 connector can also transmit one-way
	modulated infrared (IR) signals. See "Modulated IR
	pass through" on page 2-33.
M	Audio output connector (DVI 201 A D Tx [Decora] only) —
	Connect a stereo audio device to this 3.5 mm mini stereo jack to
	receive the unbalanced audio output. Figure 2-14on page 2-17
	shows how to wire the audio plug.

Pin assignments and wiring

DVI connector pin assignments

Figure 2-19 defines the pinout for the DVI protocol.

		1	8
	9	17	24		Male Connector
		Female Connector
Pin		Signal		Pin	Signal	Pin	Signal
1	TMDS data 2–			9	TMDS data 1–	17	TMDS data 0–
2	TMDS data 2+			10	TMDS data 1+	18	TMDS data 0+
3	TMDS data 2			11	TMDS data 1	19	TMDS data 0
		shield			shield		shield
4		Spare		12	Spare	20	Spare
5		Spare		13	Spare	21	Spare
6		DDC clock		14	+5 V power	22	TMDS clock
							Shield
7		DDC data		15	Ground (+5 V)	23	TMDS clock+
8	CEC control*			16	Hot Plug Detect	24	TMDS clock–

*CEC control on pin 8 is a proprietary usage, not the industry standard.

Figure 2-19 — DVI connectors

TP cable termination

NRJ-45 termination with CAT 5, CAT 5e, or

CAT 6 cable must comply with the TIA/EIA T 568A or

TIA/EIA T 568B wiring standard for all connections.

Figure 2-20 details the recommended termination of TP cables with RJ-45 connectors in accordance with either the TIA/EIA T 568A or the TIA/EIA T 568B wiring standard.

Side		Pins:		RJ-45
	1 2 3 4 5 6 78
				Connector
				TIA/EIA T	TIA/EIA T	Signal
				586 A	586 B
			Pin	Wire color	Wire color	RJ-45 #1	RJ-45 #2
			1	White-green	White-orange	Data 0+	CEC
			2	Green	Orange	Data 0–	HPD
			3	White-orange	White-green	ID Clock+	RS-232
							TX
			4	Blue	Blue	Data 1+	DDC Clk
			5	White-blue	White-blue	Data 1–	+12 V
		Insert
			6	Orange	Green	ID Clock–	RS-232
		Twisted					RX
	Pair Wires		7	White-brown	White-brown	Data 2+	DDC data
			8	Brown	Brown	Data 2–	Ground

NTerminate both ends of both cables identically, in accordance with either the TIA/EIA T 568A or the TIA/EIA T 568B wiring standard.

Figure 2-20 — TP cable termination

NDo not use Extron’s UTP23SF-4 Enhanced Skew-Free™A/V UTP cable to link the transmitter and receiver. Skew-free A/V cable was designed for most Extron

TP transmitter/receiver applications, but the

DVI 201 Tx/Rx will not work properly with this cable.

NIn order to fit in the junction box, the TP cables and RJ-45 connectors should not have a boot installed.

NIf necessary, test for proper cable connection (output 1 to input 1, output 2 to input 2) as follows:

1. Plug both TP cables into the powered unit.

2. Momentarily connect either of the cables on the opposite end into the unpowered unit‘s “2” connector.

If the unpowered unit’s Power LED is lit, the connection is correct.

If the unpowered unit’s Power LED is not lit, unplug the connector on the unpowered end and connect the other cable to the “2” connector.

2-22 DVI 201 Tx/Rx • Installation and Operation DVI 201 Tx/Rx • Installation and Operation 2-23