Extron electronic HSA 200C, HSA 200CE, HSA 200S, HSA 200SE, HSA 222C, HSA 222S 3-6, 3-7

HSA 200/222 Series • Maintenance and Modifications

HSA 200/222 Series • Maintenance and Modifications

Maintenance and Modifications, cont’d

3-6

4. Remove the four 1/16" hex head screws on the right and

left sides of the front panel (figure 3-3). Retain the screws.

Lift the panel away from the enclosure.

Figure 3-3 shows an HSA 200 model. Removing the

front panel from an HSA 222 is an identical procedure.

Lift panel out

of enclosure.

Remove 2 hex head

screws on each side.

240 - 50/60 Hz 5A

HSA 200

AUDIO

Figure 3-3 — Removing the front panel

5. With a Tweeker, push down on and

gently twist on the front of each RJ-45

connector detent to disconnect the

connector from the rear of the front panel

plug-in.

6. Pinch the top and bottom bezel detents

together and push the bezel through the

front panel.

7. Snap a replacement bezel in place. If necessary, replace the

connector icon by prying the old icon off of the connector

plug-in with a Tweeker (figure 3-4) and snapping a new

icon in place.

Icon Label

Figure 3-4 — Changing the connector icon

8. Snap the internal RJ-45 connector onto the back of the front

panel enclosure bezel plug-in.

9.(HSA 222 models only) Reach your hand through the

front panel access hole and snap the lower internal RJ-45

connectors onto the back of the lower enclosure bezel

plug-ins.

10. Replace the front panel in the surface mount enclosure and

secure it in place with the hex head screws removed in

step 4.

11.(HSA 222 models only) Replace the front access panel in

the surface mount enclosure and secure it in place with the

Phillips head screws removed in step 2.

12.(HSA 222 models only) Reinstall the surface mount

enclosure. See “Removing and Replacing the Enclosure”,

steps 6 through 11.

3-7

Contents

Main 2009 Extron Electronics. All rights reserved. Users Manual Extron USA - West HSA 200S & HSA 200SE HSA 200C & HSA 200CE HSA 222S & HSA 222C Precautions Safety Instructions English Instrucciones de seguridad Espaol Consignes de Scurit Franais Sicherheitsanleitungen Deutsch s FCC Class A Notice Chapter 1 Introduction Chapter 2 Installation Chapter 3 Maintenance and Modifications Table of Contents Table of Contents, contd Chapter One Introduction Appendix A Reference Information Appendix B Packaging for Shipment Introduction 1-2 1-3 About the Hideaway Surface Access Products Figure 1-1 HSA 200C hideaway enclosure Figure 1-2 HSA 200S hideaway enclosure Introduction 1-4 Figure 1-4 HSA 200C application 1-5 About the Extender board line driver Chapter Two Installation Installation 2-3 Preparing the Routing Template 2-2 Figure 2-1 Prepared mounting template assembly Preparing the Table and Mounting the Enclosure Preparing the table with a router Figure 2-2 Cutting the opening with a router (example) 2-6 Preparing the table with a hole saw (HSA 200C, HSA 200CE, or HSA 222CUS version only) 2-7 Figure 2-3 Cutting the opening with a hole saw Installing the HSA enclosure (all) Extron HSA 200 Underside Features and Cabling Connections Figure 2-5 HSA 200CE under-table features All HSA 200 models only HSA 200C and HSA 200S (no Extender board) only Figure 2-6 HSA 200S and HSA 200C audio connector All HSA 200 and HSA 222 models Figure 2-8 Configuration of RJ-45 connectors HSA 200CE and HSA 200SE (Extender board) only Figure 2-9 Extender board audio connector wiring 2-10 2-11 Front Panel Connectors Figure 2-12 HSA 200 front panel connectors Figure 2-13 HSA 222 front panel connectors 2-14 Figure 2-14 Audio input connector plug 2-15 Figure 2-15 Configuration of RJ-45 connectors Figure 2-16 Changing the connector icon Chapter Three Maintenance and Modifications 2-16 Pre-installation Testing and Troubleshooting (HSA 200CE and HSA 200SE Models Only) If the image does not appear or there is no sound Maintenance and Modifications 3-2 Removing and Replacing the Enclosure Replacing the Bezels 3-3 3-53-4 Figure 3-2 Releasing the bezel plug-in detent (HSA 222 models) 3-6 Figure 3-3 Removing the front panel 3-7 Figure 3-4 Changing the connector icon HSA 200/222 Series Maintenance and Modifications Replacing the Gas Lift Figure 3-5 Removing the gas lift mounting plate Figure 3-6 Front panel removal (HSA 200 models) 3-10 Figure 3-7 Front access panel removal (HSA 222 models) 3-11 Figure 3-8 Replacing the gas lift, HSA 200 model HSA 200/222 Series Maintenance and Modifications Adjusting the Top Panel Figure 3-10 Adjusting the top panel A Appendix A Reference Information Reference Information A-3A-2 Specifications 0 dBu = 0.775 Vrms. 0 dBV = 1 Vrms. 0 dBV 2 dBu. Video HSA 200SE, HSA 200CE General A-5 All nominal levels are at 10% Specifications are subject to change without notice. HSA Part Numbers A-6 A-7 HSA 200S Part number HSA 200SE Part number HSA 200C Part number HSA 200S/HSA 200SE International Models Part Part number Routing Templates Template Part number Accessories B Appendix B HSA 200C/HSA 200CE International Models Packaging for Shipment HSA 200C/HSA200CE/HSA222C US Models Packaging for Shipment Figure B-2 Installing protective strips Figure B-3 Installing the HSA into the foam shell B-3 Figure B-1 HSA 200/HSA 222 return kit Packaging for Shipment, contd