Extron electronic HSA 200C, HSA 200CE, HSA 200S, HSA 200SE, HSA 222C, HSA 222S Packaging for Shipment

HSA 200/222 Series • Packaging for Shipment

HSA 200/222 Series • Packaging for Shipment

Packaging for Shipment

2. Disconnect all cables and remove the HSA 200 or HSA 222

from the table or desk. See “Removing and Replacing the

Enclosure”, steps 1 through 4, in chapter 3, “Maintenance

and Modifications”.

3. Place the enclosure on a flat, horizontal surface. To protect

the finish, place it on a soft cloth or rubber mat.

4. Install the plastic strip (part of the return kit) to protect the

flanged edges of the top of the enclosure (figure B-2).

Figure B-2 — Installing protective strips

5. Open the top panel and insert the HSA 200 or HSA 222

into the custom cutout portion of one of the foam shells

(figure B-3).

Figure B-3 — Installing the HSA into the foam

shell

B-3

The HSA 200’s and HSA 222’s ultra-fine machined surfaces and

moving parts make them vulnerable to damage caused by

mishandling during shipment, if they are improperly packaged.

If, for any reason, you need to return an HSA to Extron, first

contact Extron to obtain a return kit. The return kit, which

reduces the chances of damage during shipment, includes a

sturdy shipping carton and foam shells custom cut to fit the

HSA (figure B-1).

Figure B-1 — HSA 200/HSA 222 return kit

Package an HSA for shipment as follows:

1. Contact the Extron S3 Sales & Technical Support Hotline to

obtain a return kit. Extron will send the return kit to the

location you specify.

The flanged edges of the top of the surface

enclosure are sharp when the HSA is removed from

the table. Exercise caution when handling to

prevent personal injury.

CAUTION

The flanged edges of the top of the surface

enclosure are bevelled to an ultra-fine thickness of

less than 0.04 (4/100)” (approximately 1 mm).

These edges are soft and can be easily nicked or

bent. Exercise caution when handling and

mounting the enclosure. Mishandling can damage

the appearance of the enclosure.

B-2

Contents

Main 2009 Extron Electronics. All rights reserved. Users Manual Extron USA - West HSA 200S & HSA 200SE HSA 200C & HSA 200CE HSA 222S & HSA 222C Precautions Safety Instructions English Instrucciones de seguridad Espaol Consignes de Scurit Franais Sicherheitsanleitungen Deutsch s FCC Class A Notice Chapter 1 Introduction Chapter 2 Installation Chapter 3 Maintenance and Modifications Table of Contents Table of Contents, contd Chapter One Introduction Appendix A Reference Information Appendix B Packaging for Shipment Introduction 1-2 1-3 About the Hideaway Surface Access Products Figure 1-1 HSA 200C hideaway enclosure Figure 1-2 HSA 200S hideaway enclosure Introduction 1-4 Figure 1-4 HSA 200C application 1-5 About the Extender board line driver Chapter Two Installation Installation 2-3 Preparing the Routing Template 2-2 Figure 2-1 Prepared mounting template assembly Preparing the Table and Mounting the Enclosure Preparing the table with a router Figure 2-2 Cutting the opening with a router (example) 2-6 Preparing the table with a hole saw (HSA 200C, HSA 200CE, or HSA 222CUS version only) 2-7 Figure 2-3 Cutting the opening with a hole saw Installing the HSA enclosure (all) Extron HSA 200 Underside Features and Cabling Connections Figure 2-5 HSA 200CE under-table features All HSA 200 models only HSA 200C and HSA 200S (no Extender board) only Figure 2-6 HSA 200S and HSA 200C audio connector All HSA 200 and HSA 222 models Figure 2-8 Configuration of RJ-45 connectors HSA 200CE and HSA 200SE (Extender board) only Figure 2-9 Extender board audio connector wiring 2-10 2-11 Front Panel Connectors Figure 2-12 HSA 200 front panel connectors Figure 2-13 HSA 222 front panel connectors 2-14 Figure 2-14 Audio input connector plug 2-15 Figure 2-15 Configuration of RJ-45 connectors Figure 2-16 Changing the connector icon Chapter Three Maintenance and Modifications 2-16 Pre-installation Testing and Troubleshooting (HSA 200CE and HSA 200SE Models Only) If the image does not appear or there is no sound Maintenance and Modifications 3-2 Removing and Replacing the Enclosure Replacing the Bezels 3-3 3-53-4 Figure 3-2 Releasing the bezel plug-in detent (HSA 222 models) 3-6 Figure 3-3 Removing the front panel 3-7 Figure 3-4 Changing the connector icon HSA 200/222 Series Maintenance and Modifications Replacing the Gas Lift Figure 3-5 Removing the gas lift mounting plate Figure 3-6 Front panel removal (HSA 200 models) 3-10 Figure 3-7 Front access panel removal (HSA 222 models) 3-11 Figure 3-8 Replacing the gas lift, HSA 200 model HSA 200/222 Series Maintenance and Modifications Adjusting the Top Panel Figure 3-10 Adjusting the top panel A Appendix A Reference Information Reference Information A-3A-2 Specifications 0 dBu = 0.775 Vrms. 0 dBV = 1 Vrms. 0 dBV 2 dBu. Video HSA 200SE, HSA 200CE General A-5 All nominal levels are at 10% Specifications are subject to change without notice. HSA Part Numbers A-6 A-7 HSA 200S Part number HSA 200SE Part number HSA 200C Part number HSA 200S/HSA 200SE International Models Part Part number Routing Templates Template Part number Accessories B Appendix B HSA 200C/HSA 200CE International Models Packaging for Shipment HSA 200C/HSA200CE/HSA222C US Models Packaging for Shipment Figure B-2 Installing protective strips Figure B-3 Installing the HSA into the foam shell B-3 Figure B-1 HSA 200/HSA 222 return kit Packaging for Shipment, contd