VersaTools® MDA 3 Series, cont’d
Furniture or projector mounting
Furniture mount or projector mount the MDA using the optional Extron MBU 123 VersaTools® under desk mounting kit (part
1. | Attach the mounting brackets to the MDA with the |
| machine screws provided (figure 5). |
8. For projector mounting, secure the MDA to a projector mount or other surface by inserting the mounting bolt through the bracket’s slotted hole.
Connections, Controls, and Indicator
See figure 6, figure 7, and figure 11 to make the following connections. The figures show all of the combinations of connectors that you may encounter with your MDA.
S-video (MDA 3SV, MDA 3SVA, MDA 3SV Dual)
Projector
Mounting
Bracket
Mounting Bolt
1Input connector (s) — Connect an
Projector
MDA 3SVA, | 1 | |
| ||
Rear Panel |
| |
MDA 3SVA | INPUT | |
| ||
POWER |
| INPUT |
12V |
| |
.5A MAX | L | R L 1 |
|
2
OUTPUTS
123
OUTPUTSBAL
R L 2 R L 3 R
Under Desk Mounting | Projector Mounting |
Figure 5 — Desk and projector mounting the MDAs
2. | If feet were previously installed on the bottom of the |
| MDA, remove them. |
3. | For furniture mounting, hold the MDA with the attached |
| brackets against the underside of the table or other |
| furniture. Mark the location of the screw holes of the |
| bracket on the mounting surface. |
4. | For furniture mounting, drill 3/32" (2 mm) diameter pilot |
| holes, 1/4" (6.3 mm) deep in the mounting surface at the |
| marked screw locations. |
5. | For furniture mounting, insert #8 wood screws into the |
| four pilot holes. Tighten each screw into the mounting |
| surface until just less than 1/4" of the screw head |
| protrudes. |
6. | For furniture mounting, align the mounting screws with |
| the slots in the brackets and place the MDA against the |
| surface, with the screws through the bracket slots. |
7. | For furniture mounting, slide the MDA slightly forward or |
| back, then tighten all four screws to secure the MDA in place. |
|
|
|
|
|
| 1 2 3 |
|
|
|
|
|
| UNBAL |
10 |
| 5 |
| 6 |
| 7 |
MDA 3AV, |
| 3 |
|
| 4 |
|
Rear Panel |
|
|
|
|
| |
MDA 3AV |
|
|
|
|
| O |
|
|
| I |
|
| |
|
|
|
|
| U | |
|
|
| N |
|
| |
|
|
|
|
| T | |
|
|
| 1 | 2 | 3 | |
POWER |
| INPUT |
| |||
12V |
|
| OUTPUTS | BAL | ||
.34A MAX |
|
|
|
|
| |
L | R | L 1 R | L 2 R | L 3 R |
| |
|
| |||||
|
|
|
|
|
| 1 2 3 |
|
|
|
|
|
| UNBAL |
10 | 5 | 6 | 7 |
Figure 6 — MDA 3 Series front and rear panels
2Out connector or Outputs (1 through 3) connectors — Connect up to three
6 | VersaTools | ® | MDA 3 Series • InstallaConnections and Controls | VersaTools | ® | ® | 7 |
|
| MDAVersaTools3 Series •MDAConnections3 Series •andInstallationControls |