Installation and Operation, cont’d

Connect the sleeve to ground (GND). Connecting the sleeve to a negative (-) terminal will damage the audio output circuits.

Unbalanced Output

Tip

See Warning

Sleeve (s)

Tip

See Warning

Balanced Output

Tip

Ring

Sleeve (s)

Tip

Ring

Wiring the audio output connector

9Autoswitching/Contact closure connector — Connect a contact closure control device to the left three pins of this 3.5 mm, 5-pole captive screw connector.

Pin 1 selects input 1 when connected to ground (pin 3).

Pin 2 selects input 2 when connected to ground (pin 3).

Pin 3 connects to the ground wire (equipment ground).

CONTACT AUTO-SW

1 2

Jumper pins 4 & 5 for autoswitching.

Contact Closure Control

Pins 4 and 5 if jumpered/shorted together will turn the autoswitching mode on. When the autoswitching mode is on, the switcher automatically switches to the input that has an active sync signal.

If both inputs have an active sync signal present, the highest input, input 2, will be used, and the input 2 indicator LED will light. If no active sync signal is present, neither input indicator LED will light.

Autoswitching overrides manual input selection. If autoswitching is on, contact closure and front panel input selection will be disabled.

If pins 4 and 5 are not connected, manual switching is enabled. Selections can be made via the front panel selection switches and the contact closure device.

If no active sync signal is present, the input 2 indicator LED will still light.

Cabling

Attach cables to the switcher as detailed in the steps below. The diagram in this section shows how the system looks when cabling is finished.

1.Attach the computers’ video output cables to the switcher via the 15-pin HD female input connectors. If the computers will provide the audio input, VGA with audio combination cables, such as the Extron VGA HRA series (#29-491-01 to #29-491-05), can be used.

2.Connect the cables from the stereo audio sources (computers or other devices such as CD players or tape decks) to the audio input jacks. The audio plug should be wired as shown below.

Tip (L)

Sleeve (Gnd)

Ring (R)

Tip (L)

Sleeve (Gnd)

3.Connect VGA cables from the switcher’s 15-pin HD female output connectors to the display devices (projectors, monitors).

4.Connect the speakers’ or other audio output device’s cable to the switcher’s audio output captive screw connector.

5.Attach the contact closure device to the left three pins of the 5-pole captive screw Contact/Auto-sw connector.

6.Connect power cords and turn on the devices in the following order: display and audio output devices (projectors, monitors, speakers), contact closure controller, SW2 VGA DA2 A /AF switcher, and input devices (computers, audio sources).

2-8

SW2 VGA DA2 A /AF • Installation and Operation

SW2 VGA DA2 A /AF • Installation and Operation

2-9

Page 9
Image 9
Extron electronic SW2 VGA DA2 AF user manual Cabling, Wiring the audio output connector

SW2 VGA DA2 AF, SW2 VGA DA2 A specifications

Extron Electronics is a renowned name in the field of audio-visual solutions, and their SW2 VGA DA2 A and SW2 VGA DA2 AF are exemplary products that reflect their commitment to quality and innovation. The SW2 VGA DA2 A is a high-performance two-input VGA distribution amplifier, which is designed to distribute a single VGA input signal to multiple outputs. On the other hand, the SW2 VGA DA2 AF offers additional features with automatic features that enhance its functionality for professional AV settings.

One of the most notable features of the SW2 VGA DA2 A is its ability to maintain signal integrity over extended distances. It supports resolutions up to 1920x1200, ensuring that video quality remains sharp and clear, regardless of how far the signal is transmitted. With its bandwidth capability of up to 400 MHz, users can be assured that the unit can handle even the most demanding high-resolution signals without degradation.

The SW2 VGA DA2 AF includes both the core features of the SW2 VGA DA2 A while adding automatic input selection. This feature allows the unit to automatically switch between VGA input sources based on the presence of a signal, which is a valuable time-saver in settings where equipment may frequently change, such as classrooms or conference rooms. Furthermore, it offers a flexible control option that integrates seamlessly into various AV control systems.

Signal amplification is another critical feature of both models, which ensures that the VGA output signals are strong enough to drive multiple displays with ease. Each output is provided with independent signal processing, allowing for optimal performance across all connected devices. The units also feature a compact design, making them easy to integrate into any AV rack or installation.

Both the SW2 VGA DA2 A and SW2 VGA DA2 AF come equipped with Extron’s superior build quality, ensuring durability over prolonged use. Their reliability makes them suitable for a wide array of applications, including corporate presentations, educational environments, and broadcast studios.

In summary, the Extron SW2 VGA DA2 A and SW2 VGA DA2 AF are exceptional VGA distribution amplifiers that excel in performance and versatility. With advanced technology, exceptional signal integrity, and user-friendly features, they stand as ideal solutions for any AV distribution requirement, whether in corporate environments, educational institutions, or professional media setups.