Setup Guide — SW RGBHV Series Switchers
Setup Guide — SW RGBHV Series Switchers
This guide provides quick start instructions for an experienced installer to set up and operate the SW RGBHV and SW RGBHV A
switchers.
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the switcher as required.
Step 2 — Inputs
•Connect up to 2, 4 or 6 RGBHV, RGBS, RGsB, or RsGsBs video or component video inputs to the Input connectors.
•Audio models — Connect up to 2, 4 or 6 stereo or mono audio inputs
to the |
|
captive screw | Tip |
connectors. | Sleeve |
|
L
RGBHV
G B
RGBS
R G B
Tip | R | |
Sleeve | ||
| ||
Unbalanced Stereo Input |
|
RGsB, |
|
|
|
RsGsBs, |
|
|
|
Component | R | G | B |
H/HV V
H/HV V
H/HV V
Step 5 — Power
Plug a standard IEC power cord between the switcher’s power connector and a 100 VAC to 240 VAC, 50 or 60 Hz power source.
Operation
Switch mode | AUTO |
Set the rear panel switch to Auto for autoswitch mode (the switcher automatically |
|
switches to the |
|
manual switch mode. The front panel Auto Switch Active LED lights when the | MANUAL |
switcher is in autoswitch mode. |
|
Switch inputs in normal switch mode
Press and release the desired input button.
Adjust audio level (audio models)
You can set the input level of audio gain or attenuation via the front panel or the Remote port to be compatible with a wide range of line level sources. Individual input audio levels can be adjusted so that there is no noticeable volume difference among sources. This function also eliminates the need for separate preamps or attenuators, when used with professional (higher
line level) and consumer (lower line level) audio equipment.
Adjust the audio from the front panel as follows:Press 1 and release.
Do not tin the wires! | Tip | L | |
Ring | |||
|
| ||
| Sleeve (s) |
| |
| Tip | R | |
| Ring | ||
|
|
Balanced Stereo Input
1. Press and release the desired input button.
2. Press and hold the Audio Conf./Save button until the Audio Conf./ Save LED begins to blink. The approximate level is indicated by the input LEDs and the polarity by the ±dB LEDs.
1
2 | Press |
and hold. |
Step 3 — Outputs
•Connect an RGBHV, RGBS, RGsB, or RsGsBs video or component video display or other device to the Output connectors. Make connections as shown for step 3.
•Audio models
NThe input LEDs display the approximate level of attenuation. The +dB LED indicates the level is gain (positive).
The - dB LED indicates the level is attenuation (negative).
For details about reading the displayed value, refer to the full SW RGBHV Switchers User’s Manual, available at www.extron.com.
B
CONF/SAVE
Conf/Save blinks. Release the button.
| Tip | L | Tip | L | |
| NO GROUND HERE. | Ring | |||
|
|
| |||
| Sleeve(s) |
| Sleeve(s) |
| |
Do not tin the wires! | Tip | R | Tip | R | |
NO GROUND HERE. | Ring | ||||
|
|
|
Unbalanced Stereo Output Balanced Stereo Output
CConnect the sleeves to ground (Gnd). Connecting the sleeve to a negative
3. Press and release the >and <buttons to increase and decrease the audio level by 1 dB per push of the button, or press and hold the buttons to increase or decrease the level by 3 dB per second.
|
|
|
|
| Press | Press |
3 | 1 | 2 | 3 | 4 | 5 | 6 |
|
|
|
|
|
|
Step 4 — Remote port
Connect a host device, such as a computer or touch panel control via
closure device to the switcher | 5 |
| 1 |
via the |
| ||
|
|
| |
remote control of the switcher. |
|
|
|
To command a switch under |
| 9 | 6 |
contact closure control, |
| ||
momentarily short an input’s |
| Female |
pin on the remote connector to | ||
9600 Baud, 8, N, 1 | ||
ground (the switcher must be in | ||
| ||
normal [manual] mode). |
|
Pin | Contact | Function | ||
|
|
| closure |
|
1 |
| — | In #1 | Input #1 |
2 |
| TX | — | Transmit data |
3 |
| RX | — | Receive data (+) |
|
|
|
|
|
4 |
| — | In #2 | Input #2 |
5 |
| Gnd | Gnd | Signal ground |
6 |
| — | In #3 | Input #3 |
7 |
| — | In #4 | Input #4 |
8 |
| — | In #5 | Input #5 |
|
| — | In #6 | Input #6 |
|
|
|
|
|
Press
4. Press and release the Audio Conf./Save button to exit. The Audio and release. Conf./Save LED goes out.
4 CONF/SAVE
Extron USA - West Extron USA - East Extron Europe | Extron Asia | Extron Japan | Extron China | Extron Middle East |
Headquarters |
|
|
|
|
NFor complete descriptions of remote control of the switcher using the applicable Simple Instruction Set (SIS™) commands and/or the Universal Switcher Control Program, refer to the full SW RGBHV Switchers User’s Manual, available at www.extron.com.
| +800.633.9876 | +800.3987.6673 | +800.7339.8766 | +81.3.3511.7655 | +400.883.1568 | +971.4.2991800 | |
+800.633.9876 | Inside USA / Canada Only | Inside Europe Only | Inside Asia Only | +81.3.3511.7656 FAX | Inside China Only | +971.4.2991880 FAX | |
Inside USA / Canada Only | +1.919.863.1794 | +31.33.453.4040 | +65.6383.4400 |
| +86.21.3760.1568 |
| Rev. A |
|
|
| |||||
+1.714.491.1500 | +1.919.863.1797 FAX | +31.33.453.4050 FAX | +65.6383.4664 FAX |
| +86.21.3760.1566 FAX |
| 04 09 |
+1.714.491.1517 FAX |
| © 2009 Extron Electronics. All rights reserved. |
|
| |||
|
|
|
| ||||
|
|
|
|
|