Installation and Operation, cont’d
1. Remove the three screws on each side and the one or two screws on top of the cover (figure
Remove (7) |
|
|
|
|
|
|
|
|
Screws |
|
|
|
|
|
|
|
|
Lift Cover |
|
|
|
|
| TP R AV | ||
|
|
|
|
| or | |||
straight up |
|
|
|
|
| TP R BNC AV | ||
|
|
|
|
| UT | B | ||
|
|
|
| UTP |
|
|
| |
|
|
|
|
|
|
| ||
|
| A |
| A |
|
|
|
|
|
|
|
|
| L |
|
|
|
|
| EO |
|
| UD | IO |
|
|
| VID |
|
|
|
|
| ||
|
| R | A |
|
| Remove 1 (TP R AV) or | ||
PUT |
|
|
|
|
|
| ||
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| 6 (TP R BNC AV) |
|
|
|
|
|
|
|
| BNC Hex Nuts |
| J10 |
|
|
|
|
|
| |
| J11 |
|
|
|
|
|
| |
|
|
| Wire Pair | Wire Pair |
Mounting the receiver
Rack mounting (TP R BNC A, TP R BNC AV, TP R 15HD A)
TP R BNC A, TP R BNC AV, or TP R 15HD AV — For optional rack mounting, mount the receiver on a 19" 1U Universal Rack Shelf (Extron part
3&6* |
| 7&8 |
| |||||
|
|
|
|
| J11 |
|
|
|
|
|
|
|
|
|
|
| |
1 |
|
|
| 1 |
|
|
| |
|
|
|
| |||||
Wire Pair | Wire Pair | |||||||
3&6* |
| 7&8 |
| |||||
|
|
|
|
| J10 |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| 1 |
|
| 1 |
|
AV board in TPR BNC AV | * TPX Compatible |
or |
|
TP R AV |
|
Figure | |
2. Using an Extron BNC extraction tool (part |
| R |
LE | GB |
VEL |
|
TP PEAK | ING | |
R |
| |
| 15H | |
|
| D A |
| R |
LEVEL | GB |
|
TP | P |
|
|
EAK | ING | ||
| R |
| |
|
| 15H | |
|
|
| D A |
(2)
Use 2 Mounting Holes on Opposite Corners
| R |
LEVEL | GB |
|
TP PEAK | ING | |
R |
| |
| 15H | |
|
| D A |
VIDEO
RGB
TP R |
|
BNC | AV |
| 14 mm, deep well socket with thin walls, remove the one or |
| six hex nuts securing the BNC connectors to the rear panel. |
3. | Slide the cover forward until the cover clears the BNC |
| connectors and then lift the cover off. |
4. | Locate J10 and J11 on the composite video printed circuit |
| board. See figure |
a. For compatibility with redesigned (modified) receivers and the TPX 88 A, ensure that pin 1 is jumpered to pin 2 on both jumper locations.
b. For compatibility with older (unmodified) receivers, ensure that pin 2 is jumpered to pin 3 on both jumper locations.
5. Replace the cover, and reinstall the screws and BNC connector hex nut(s).
Figure 2-3 — Rack mounting the TP R 15HD A and
TP R BNC AV
TP Receivers • Installation and Operation | TP Receivers • Installation and Operation |