Installation and Operation, cont’d
Audio
All Extron TP receivers receive and output stereo audio. All receivers except the TP R 15HD A output the audio on both left and right RCA connectors and on 3.5 mm,
TP R BNC A and TP R AV — Wire the external 15V power supply into this
screw connector only.
7Stereo audio output connectors — Connect left and right stereo audio cables between these rear panel RCA connectors and the output device’s stereo audio inputs.
SmoothRidges
Power Supply
Output Cord
Power 12VDC
Captive
Screw
Connector
Power 15VDC
Captive
Screw
Connector
N/C
Only analog, line level, unbalanced audio signals can be output on these connectors.
8Stereo audio
Tip | Tip |
See warning | Ring |
Sleeve | Sleeve (s) |
Tip | Tip |
See warning | Ring |
Unbalanced Output | Balanced Output |
Figure |
TP R 15HD A | TP R BNC A |
| TP R AV |
Figure 2-9 — Power connector wiring
TP R 15HD A — Wire the external 15V power supply into this
Termination of TP cable
Figure
CAUTION | Connect the sleeve to ground (Gnd). Connecting |
| the sleeve to a negative |
| audio output circuits. |
If only an audio signal, no video, is received, connect a ground wire between the chassis ground and an earth ground in the equipment rack or other grounded device. If the receiver is not grounded, a crackling sound may be heard in the audio output.
Power connector
9PowerTP R BNC AV — Plug a standard IEC power cord into this connector to connect the TP R BNC AV to a 100 to 240VAC, 50 Hz or 60 Hz power source.
If the distance between the transmitter and receiver is too great for the receiver to power the transmitter, the video image will be missing, distorted, or noisy, or the receiver’s Manual/Auto LED will flash. The transmitter
Side | Clip Down | ||
| 1 2 3 4 5 6 7 8 |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 2 3 4 5 6 7 8
1&2
3&6 4&5
|
|
|
|
| RGB video and audio | AV Video and audio | ||
Pin | Wire color | Signal | Level | Signal | Level | |||
|
|
|
|
|
|
|
|
|
1 | Red/V. sync+ | ±0.35V | Video+ | +0.35V | ||||
|
|
|
|
|
|
|
|
|
2 | Green | Red/V. sync- | ±0.35V | Video- | ||||
|
|
|
|
|
|
|
|
|
3 | Audio & | +15V with | Audio+* & | +15V | ||||
|
|
|
|
| power | ±0.5 V | power+ |
|
|
|
|
|
|
|
|
|
|
4 | Blue | Green+ | +0.35V | Reserved | None | |||
|
|
|
|
|
|
|
|
|
5 | Green- | Reserved | None | |||||
|
|
|
|
|
|
|
|
|
6 | Orange | Audio & | ±0.5 V | 0V | ||||
|
|
|
|
| power |
| power- |
|
7 | Blue/H. sync+ | ±0.35V | Reserved | None | ||||
|
|
|
|
|
|
|
|
|
8 | Brown | Blue/H. sync- | ±0.35V | Reserved | None | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| * Audio can be jumpered to wire pair 7 and 8. | |||
7&8 |
|
|
| See Audio jumpers in this chapter. |
| |||
|
| Twisted |
|
|
| |||
|
|
|
| Pairs |
|
|
|
|
requires a local 15V power supply.
Figure 2-10 — TP cable termination
| TP Receivers • Installation and Operation |