Installationtal ation, cont’d

Rear Panel Connectors

TP T 15HD 45

TP T A 45

+

AUDIO +

- AUDIO -

Digital Audio Input Captive Screw Direct Insertion Connector

 

TP T 15HD 45

 

1a

12 VDC

 

8

4

.5A MAX.

 

7

1b

AUDIO

OUTPUT

43 5 6

3

 

AUDIO

 

 

 

 

 

 

2

 

 

 

 

1

 

TP T A 45

AUDIO

AUDIO

12 VDC

.5A MAX.

Remove power before wiring.

The wire gauge should be 14 -22 AWG and the maximum distance between the modules should not exceed 25 feet.

2 Video and audio output 8-pin spring force connector — Attach

a UTP cable from a TP receiver to the 8-pin spring force

connector. Wire this connector according to the following pin

Figure 2-1 — Rear panel views

1a Power input captive screw connector — Connect the included

12 VDC external power supply to the 2-pole female direct insertion captive screw connector.

The TP T 15HD 45 and the TP T A 45 share a single power supply. Neither one can be remotely powered by the attached receiver.

AA

+

+

12 VDC

 

 

.5A MAX.

 

 

 

 

 

SECTION A–A

Captive Screw

 

Power Supply

 

Direct Insertion Connector

 

 

 

 

 

 

 

 

Output Cord

 

 

 

 

 

 

 

 

The two power supply leads must be kept separated

 

 

 

 

 

 

 

 

 

while the power supply is plugged into an electrical

 

 

 

 

 

outlet. Remove power before wiring.

 

 

 

Power supply voltage polarity is critical. Incorrect

 

CAUTION

 

 

 

 

 

 

voltage polarity can damage the power supply and

the transmitter. Identify the power cord negative lead by the ridges on the side of the cord.

When stripping the wire ends, please note that stripped wire ends that are too short may pull out from the captive screw connector and stripped wire ends that are too long could possibly touch and short together.

1b Captive screw digital audio input connector — Connect the digital audio input cables from the TP T A 45 (if installed) to the 2-pole female direct insertion captive screw connector.

assignment table.

Twisted Pair Pin Assignments

Pin

 

Signal

TIA/EIA T-568-A

TIA/EIA T-568-B

 

 

Wire Color

Wire Color

 

 

 

 

 

 

1

red / vertical sync +

white-green

white-orange

 

 

 

 

 

 

 

 

2

red / vertical sync -

green

orange

 

3

digital audio +

white-orange

white-green

 

 

 

 

 

 

 

 

4

green +

 

blue

blue

 

5

green -

 

white-blue

white-blue

 

 

 

 

 

 

 

 

6

digital audio -

orange

green

 

7

blue / horizontal sync +

white-brown

white-brown

 

 

 

 

 

 

 

 

8

blue / horizontal sync -

brown

brown

 

 

 

 

 

 

 

 

 

 

T-568-A is recommended when using Extron Enhanced

 

 

 

 

Skew-Free™ A/V UTP cable.

 

 

 

Do not connect the transmitter to a computer data

CAUTION

 

 

 

or telecommunications network.

Using the included tweeker tool and observing the correct wiring colors in the previous table, insert the stripped wire ends (see note below) of the twisted pairs into the spring force connector, as shown in the following diagram.

Strip approximately 0.43" (1.1 cm) of insulation from each individual wire on one end of a TP cable.

2-2 TP T 15HD 45 and TP T A 45 • Installation

TP T 15HD 45 and TP T A 45 • Installation 2-3

Page 7
Image 7
Extron electronic TP T A 45, TP T 15HD 45 user manual Installationtal ation, cont’d Rear Panel Connectors

TP T A 45, TP T 15HD 45 specifications

Extron Electronics has long been a leader in high-quality AV solutions, and the TP T 15HD 45 and TP T A 45 are no exceptions. These transmitter and receiver units are part of Extron's line of products designed for long-distance signal transmission while preserving high-definition video and audio quality.

The TP T 15HD 45 is a state-of-the-art wall plate transmitter that is particularly crafted for sending HDMI signals over twisted-pair cabling. With support for 4K resolutions at 60 Hz, it ensures that users experience stunning video quality, making it ideal for advanced display setups in commercial and educational environments. It is designed to work seamlessly with Extron's receiver products, facilitating the transmission of both video and audio signals up to 100 meters away when using a compatible twisted-pair cable.

One of the main features of the TP T 15HD 45 is its EDID and HDCP management capabilities. This ensures that the proper video format is always communicated between the source and display, providing a smooth user experience. The unit is equipped with a built-in audio de-embedding function, which allows audio signals to be routed separately if needed. The design includes various input options, including a convenient HDMI input, making it suitable for various equipment setups.

The TP T A 45, on the other hand, serves as a versatile wall plate receiver for HDBaseT signals. Supporting 4K video content and various audio formats, it excels at rejoining and transmitting signals from a centralized AV system to a remote display device. Like its counterpart, it is built to handle signals for distances up to 100 meters without any degradation in quality.

Both units feature signal boosting technology, which helps maintain video integrity across extended distances. The robust construction and sleek design make them perfect for installation in various environments, ranging from classrooms and conference rooms to control centers and command stations.

In summary, the Extron TP T 15HD 45 and TP T A 45 are top-tier products in the realm of AV distribution technology. Their exceptional performance, support for high-definition signals, and versatile connectivity options make them invaluable tools for modern AV installations, delivering both quality and reliability in signal transmission.