Fender 160, 100H manual Specifications

1

2	3	4	5	6	7	8	9
	STAGE 100H		STAGE 100
	SPEAKER		SPEAKER
	JACKS		JACK

1.POWER SWITCH - Turns the AC power ON and OFF.

2.LINE CORD - This amplifier is equipped with an IEC grounding type supply cord to reduce the possibility of shock hazard. Be sure to connect it to a grounded AC receptacle in accordance with the voltage and frequency ratings listed on the rear panel under INPUT POWER.

•NOTE: Items 3 and 4 apply only to the Stage 100H.

3.SPEAKER OUTPUT (8Ω minimum) - Use this out- put jack when only one 8Ω speaker enclosure is to be connected to the Stage 100H. If two 8Ω

speaker enclosures are to be connected, use both parallel speaker output jacks (total load of 4Ω).

4.SPEAKER OUTPUT (4Ω minimum) - Use this output jack when one 4Ω speaker enclosure is to be con-

nected to the Stage 100H. (Using this jack inter- nally switches the Stage 100H to accept a 4Ω load.)

• NOTE: Item 5 applies only to the Stage 100.

5.EXTERNAL SPEAKER (8Ω minimum) - Use this output jack when one 8Ω speaker enclosure is to be connected to the Stage 100 for additional out- put. The Stage 100’s internal speaker must be connected while using this jack.

6.LINE OUT - This balanced XLR line-level output is designed for connection to an external power amplifier or main house mixer. The signal from this output jack includes all tone shaping done by the amplifier.

7.RETURN - This 1/4 inch, unbalanced, TS, line- level input jack is designed to accept a signal from external effects devices or another amplifier in a “daisy-chain” configuration.

8.SEND - This 1/4 inch, unbalanced, TS, line-level output jack is designed to feed the preamp signal to external effects devices or to an “add-on” amplifier in a daisy-chain configuration.

9.FOOTSWITCH - Connect the footswitch at this jack. The two-button footswitch enables switching between Normal and Drive channels and ON/OFF switching of the MORE DRIVE pre-amplifier boost. Using this jack disables these switching functions from the front panel. NOTE: Connecting the footswitch with an unshielded speaker type cord is preferable to using a shielded coaxial guitar cord.

Specifications

		Stage 100 (combo)		Stage 160 (combo)		Stage 100H (head only)
TYPE:		PR 401		PR 400		PR 453
PART NUMBER:		22-6700 (120V, 60Hz) US		22-6800 (120V, 60Hz) US		22-6900 (120V, 60Hz) US
		22-6730 (240V, 50Hz) Aust		22-6830 (240V, 50Hz) Aust		22-6930 (240V, 50Hz) Aust
		22-6740 (230V, 50Hz) UK		22-6840 (230V, 50Hz) UK		22-6940 (230V, 50Hz) UK
		22-6760 (230V, 50Hz) Eur		22-6860 (230V, 50Hz) Eur		22-6960 (230V, 50Hz) Eur
		22-6770 (100V, 50/60Hz) Jpn		22-6870 (100V, 50/60Hz) Jpn		22-6970 (100V, 50/60Hz) Jpn
POWER REQUIREMENTS:		400W		400W		400W
POWER OUTPUT:		100W RMS into 8Ω @ 5%THD		160W RMS into 4Ω @ 5%THD		100W RMS into 8Ω @ 5%THD
(WITH EXTENSION SPEAKER):		160W RMS into 4	Ω @ 5%THD	N/A		160W RMS into 4	Ω @ 5%THD
INPUT IMPEDANCE:		INPUT 1: 850kΩ, INPUT 2: 66kΩ		INPUT1: 850kΩ, INPUT 2: 66kΩ		INPUT1: 850kΩ, INPUT 2: 66kΩ
FX SEND OUTPUTIMPEDANCE:		1kΩ		1kΩ		1kΩ
FX RETURN INPUT IMPEDANCE:		10kΩ		10kΩ		10kΩ
POWER AMPIN SENSITIVITY:		810mV for 160W into 4 Ω @1kHz		810mV for 160W into 4 Ω @1kHz		810mV for 160W into 4 Ω @1kHz
		620mV for 100W into 8 Ω @1kHz		N/A		620mV for 100W into 8 Ω @1kHz
FUSE:		4A125V for 100V / 120V ver		4A125V for 100V /120V ver		4A125V for 100V /120V ver
		2A250V for 230V / 240V ver		2A250V for 230V / 240V ver		2A250V for 230V / 240V ver
FOOTSWITCH:		2 Button - (P/N 050419)		2 Button - (P/N 050419)		2 Button - (P/N 050419)
		Normal/Drive, Drive/More Drive		Normal/Drive, Drive/More Drive		Normal/Drive, Drive/More Drive
SPEAKER COMPLIMENT:		One 8Ω Celestion G12T-100		Two 8Ω Celestion G12T-100		N/A
		12” speaker (P/N 054420)		12” speakers (P/N 054420)
DIMENSIONS:	HEIGHT:	17.5 in.	(45 cm)	18.5 in.	(47 cm)	8.5 in.	(22 cm)
	WIDTH:	22.4 in.	(57 cm)	26.1 in.	(66 cm)	22.4 in.	(57 cm)
	DEPTH:	10.2 in.	(26 cm)	10.3 in.	(26 cm)	9.5 in.	(24 cm)
WEIGHT:		42 lbs.	(19.1 kg)	53 lbs.	(24.1kg)	24 lbs.	(10.9 kg)

Product specifications are subject to change without notice.

5