1. Inspect Exterior Hoods at least once a month.
Make sure exhaust and fresh air supply hoods are not blocked or
restricted by leaves, grass, or snow. In winter, it is especially
importantto make sure snow is not blocking the hoods or that frost
hasnot built up on the wire mesh (bird screen).
WARNING:Blockage of hoods may cause an imbalance.
2. Clean Air Filters (clean twice a year)
The standard filters equipped with your HRV are removable and
washable.
a) simply open access door and slide core out
b) remove filter clips
c) once clips are removed filters can be taken off the core to be
rinsedwith water or a combination of mild soap and water. Do
notclean in the dishwasher
d) to re-assemble, place clean filter(s) (wet or dry) back into their
positions against the core and return clips to their original
position
e) slide core back into its’ original position
3. Clean Core Twice a Year
a) open access door.
b) carefully grip ends of core and pull evenly outward. Core may
besnug, but will slide out of the channel
c) once removed from the cabinet remove filters
d) wash core in warm soapy water (do not use dishwasher)
e) install the clean filters
f) install clean core
Note:Core installation label on the outer end of the core.
To install the clean core:
a) first mount the bottom flange of the core guide into the bottom
Hchannel approximately 1/4” (6mm)
b) mount the left or right side flange of the core guide
approximately1/4” (6mm) followed by the other side
c) mount the top flange of the core guide into the top H channel
approximately1/4” (6mm).
d) with all four corners in place and the core straight and even,
push hard in the centre of the core until the core stops on the
backof the cabinet.
NOTE: Core will appear to stick out from cabinet approximately 1/8”
(3mm). This is designed this way so that the access door will fit tight
againstthe core.
4. Motors - Maintenance Free
5. Drain (condensate) Line - Clean once a year
Inspectdrain line, drain spout, and “P” trap for blockage, mould or
kinks. Flush with warm soapy water and replace if worn, bent or
unableto clean.
6. Clean Duct Work if Required
Theduct work running to and from the HRV may accumulate dirt.
Wipe and vacuum the duct once every year. You may wish to
contacta Heating/Ventilation company to do this.
7. General Maintenance - Twice a Year
Wipe down the inside of the cabinet with a damp cloth to remove
dirt,bugs, and debris that may be present.
8. Cleaning the Fans
Fans may accumulate dirt causing an imbalance and/or excessive
vibration of the HRV. A reduction in the air flow may also occur.
In new construction this may result w ithin the first year due to
heavy dust and may occur periodically after that over time
dependingon the outdoor conditions.
• unplugthe HRV and open the service door
• removethe core
• remove ducting (metal and/or flexible insulated type) from
the red and/or blue ports which are connected immediately
in-linewith the fan assembly
• use a small brush, such as an old toothbrush or pipe cleaner,
andinsert first
(a) through the large opening of the fan
assemblyand then
(b) through the smaller opening in the end
ofthe fan assembly.
• scrub individual fan blades until clean. Avoid moving or
damagingbalancing flat weight, clip is usually found on one
ormore of the fan blades
• vacuumand wipe
• reassemble making sure ducting is reattached firmly and
insulationand moisture barrier are sealed and taped
Before attempting this task, thought should be given to having a
qualifiedservice technician complete the service work.
Maintenance Routine for HRV
Electric shock hazard. Can cause
injury or death. Before attempting to
perform any service or maintenance,
turn the electrical power unit OFF at
disconnect switch(es). Unit may have
multiplepower supplies.
WARNING
7