![](/images/new-backgrounds/1110980/11098043x1.webp)
FS-8700-103_ATMI_TGM_Serial ManualPage 22 of 28
Appendix C. Driver Error Messages
| Message |
|
|
| Notes and Corrective Action∼ | |
| TGM:#1 Err. Diagnostic #1. | If this message is printed an internal diagnostic has been | ||||
| generated. Contact FieldServer tech support for help. | |||||
|
|
|
|
|
| |
| TGM:#2 Err. TGM_Function not | Each Map Descriptor must have the parameter called | ||||
| specified. |
|
|
| “TGM_Function” set. See section 4.4.22 | |
| TGM:#3 FYI. Use an Array | This message may be ignored. For more information read | ||||
| called | <%s> | to | expose | Appendix C.1 | |
| diagnostics. |
|
|
|
| |
|
|
|
|
|
| 4a: The text string “CUR=” could not be found in the QLA |
|
|
|
|
|
| report. |
|
|
|
|
|
| 4b: The text string “GAS=” could not be found in the QLA |
|
|
|
|
|
| report. |
|
|
|
|
|
| 4c: The text string “STATUS=” could not be found in the |
| TGM: #4c Err. Bad format in | QLA report. | ||||
| If the error is printed rarely and data is being stored | |||||
| latest | area | report. Discarding | correctly then the error probably arises from a corrupted | ||
| data. |
|
|
|
| message. If the error occurs frequently then it is possible |
|
|
|
|
|
| |
|
|
|
|
|
| that the report format has changed and the driver firmware |
|
|
|
|
|
| may require an update. To facilitate the evaluation of the |
|
|
|
|
|
| problem, take a serial communications log, ensuring at least |
|
|
|
|
|
| one of the errors occurs during the log, and then contact |
|
|
|
|
|
| Tech Support. |
|
|
|
|
|
| This message is printed to alert you to the fact that the |
| TGM: #5 FYI. atmitgm.ini being | malfunction list is being based on the contents of a TGM | ||||
| used for malfunctions |
| config file. Refer to Appendix B.7. If you expect the driver to | |||
|
|
|
|
|
| be using this list, ignore the message. |
| TGM: #6 FYI. You could have | This message is printed to alert you to the possibility that | ||||
| used a TGM config file to define | |||||
| malfunctions. Working with hard | the TGM config file can be used with this driver. Refer to | ||||
| coded list. |
|
|
| Appendix B.7. | |
|
|
|
|
| ||
| TGM: | #7 | Err. | Driver | cannot | The Map Descriptor function has been set so that the driver |
| write. MD=%s |
|
| will attempt to write to the TGM. Writing is not possible. | ||
|
|
| Change the function to a read.2 | |||
| TGM: | #8 | Err. | Array=%s too | This error is printed when the driver attempts to store data | |
| short. Act/Rqd=%d/%d |
| from the QLA report. Modify the length of the Data Array as | |||
|
| discussed in section 4.1.2 | ||||
| TGM: #9 FYI. Duplicate Gas | This message may be safely ignored. It is printed to alert | ||||
| Name=<%s>. |
|
| you to the fact that the driver has updated the Gas Name | ||
| Value | has | been | updated | ||
| from=%d to=%d |
| table so that default values have been modified. | |||
|
|
|
2 Modify the configuration CSV file. Download the modified file to the FieldServer and Reset the FieldServer for the changes to take effect.
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com Tel: (408)